Victor Henrique Rodrigues Cardoso

Dr. Victor Henrique Rodrigues Cardoso

Federal University of Para, Belém, Pará, Brazil
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 May 2021 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
Victor Henrique Rodrigues CardosoVictor Henrique Rodrigues Cardoso
Victor Henrique Rodrigues Cardoso
MGMaria Giraldi
Maria Giraldi
CFCindy Stella Fernandes
Cindy Stella Fernandes
MSMarcelo Silva
Marcelo Silva
JCJoão Weyl Costa
João Weyl Costa
In this article, we proposed a simple optical sensor for flow measurement. The sensor structure is based on an in-line Mach-Zehnder interferometer formed by splicing an input single-mode fiber section and an output single-mode fiber section to a single-mode fiber sandwiched by two multimode fibers; it is called SMSMS sensor. The proposed sensor presents a high sensitivity due to low order modes that propagate in the middle single-mode fiber (SMF) cladding. The sensor is experimentally investigated and validated in which the results show good agreement between the optical power and flow for monitoring single- and two-phase flows using water and air fluids. Using this sensor, it is possible to identify the presence of air in the pipeline, in addition to the identification of the flow pattern. Thus, the proposed sensor is an interesting alternative for measuring single- and two-phase flows.

9 October 2022 in Sensors
Verified
Journal Article
Open access
PDF file
Victor Henrique Rodrigues CardosoVictor Henrique Rodrigues Cardoso
Victor Henrique Rodrigues Cardoso
Paulo CaldasPaulo Caldas
Paulo Caldas
MGMaria Giraldi
Maria Giraldi
Orlando FrazãoOrlando Frazão
Orlando Frazão
JCJoão Weyl Costa
João Weyl Costa
JSJosé Luís Santos
José Luís Santos
An optical strain gauge based on a balloon-like interferometer structure formed by a bent standard single-mode fiber combined with a 3D printer piece has been presented and demonstrated, which can be used to measure displacement. The interferometer has a simple and compact size, easy fabrication, low cost, and is repeatable. The sensor is based on the interference between the core and cladding modes. This is caused by the fiber’s curvature because when light propagates through the curved balloon-shaped interferometer region, a portion of it will be released from the core limitation and coupled to the cladding. The balloon has an axial displacement as a result of how the artwork was constructed. The sensor head is sandwiched between two cantilevers such that when there is a displacement, the dimension associated with the micro bend is altered. The sensor response as a function of displacement can be determined using wavelength shift or intensity change interrogation techniques. Therefore, this optical strain gauge is a good option for applications where structure displacement needs to be examined. The sensor presents a sensitivity of 55.014 nm for displacement measurements ranging from 0 to 10 mm and a strain sensitivity of 500.13 pm/μϵ.

17 June 2022 in Sensors
Verified
Journal Article
Open access
PDF file
Victor Henrique Rodrigues CardosoVictor Henrique Rodrigues Cardoso
Victor Henrique Rodrigues Cardoso
Paulo CaldasPaulo Caldas
Paulo Caldas
MGMaria Giraldi
Maria Giraldi
CFCindy Stella Fernandes
Cindy Stella Fernandes
Orlando FrazãoOrlando Frazão
Orlando Frazão
JSJosé Luís Santos
José Luís Santos
In many areas, the analysis of a cylindrical structure is necessary, and a form to analyze it is by evaluating the diameter changes. Some areas can be cited: pipelines for oil or gas distribution and radial growth of trees whose diameter changes are directly related to irrigation and the radial expansion since it depends on the water soil deficit. For some species, these radial variations can change in around 5 mm. This paper proposes and experimentally investigates a sensor based on a core diameter mismatch technique for diameter changes measurement. The sensor structure is a combination of a cylindrical piece developed using a 3D printer and a Mach–Zehnder interferometer. The pieces were developed to assist in monitoring the diameter variation. It is formed by splicing an uncoated short section of MMF (Multimode Fiber) between two standard SMFs (Singlemode Fibers) called SMF-MMF-SMF (SMS), where the MMF length is 15 mm. The work is divided into two main parts. Firstly, the sensor was fixed at two points on the first developed piece, and the diameter reduction caused dips or peaks shift of the transmittance spectrum due to curvature and strain influence. The fixation point (FP) distances used are: 5 mm, 10 mm, and 15 mm. Finally, the setup with the best sensitivity was chosen, from first results, to develop another test with an optimization. This optimization is performed in the printed piece where two supports are created so that only the strain influences the sensor. The results showed good sensitivity, reasonable dynamic range, and easy setup reproduction. Therefore, the sensor could be used for diameter variation measurement for proposed applications.

10 November 2019
Verified
Conference Paper
Closed access
Victor Henrique Rodrigues CardosoVictor Henrique Rodrigues Cardoso
Victor Henrique Rodrigues Cardoso
FTF. M. Takeda
F. M. Takeda
CFC. S. Fernandes
C. S. Fernandes
MGM. T. R. M. Giraldi
M. T. R. M. Giraldi
JCJ. C. W. A. Costa
J. C. W. A. Costa
Two Mach-Zehnder Interferometers based on Core Diameter Mismatch structures are proposed and experimentally investigated for curvature measurement. The sensing configuration consists of an input SMF, a section of SMF spliced between two MMFs and an output SMF. The proposed sensor generates interference patterns when it is bent, causing wavelength shifts. In this paper two lengths are used for the MMFs: 3mm and 4mm.

13 October 2022 in EPJ Web of Conferences
Verified
Journal Article
Open access
PDF file
Victor Henrique Rodrigues CardosoVictor Henrique Rodrigues Cardoso
Victor Henrique Rodrigues Cardoso
Paulo CaldasPaulo Caldas
Paulo Caldas
MGM. Thereza R. Giraldi
M. Thereza R. Giraldi
OFOrlando Frazão
Orlando Frazão
JCJoão Costa
João Costa
JSJosé L. Santos
José L. Santos
This work presents preliminary results of the ϕ -shaped sensor mounted on support designed by additive manufacturing (AM). This sensor is proposed and experimentally demonstrated to measure the radial variation of cylindrical structures. The sensor presents an easy fabrication. The support was developed to work using the principle of leverage. The sensing head is curled between two points so that the dimension associated with the macro bend is changed when there is a radial variation. The results indicate that the proposed sensor structure can monitor radial variation in applications such as pipelines and trees.

10 April 2024 in Measurement Science and Technology
Verified
Journal Article
Closed access
Victor Henrique Rodrigues CardosoVictor Henrique Rodrigues Cardoso
Victor Henrique Rodrigues Cardoso
Paulo CaldasPaulo Caldas
Paulo Caldas
MGMaria Giraldi
Maria Giraldi
MCMaria Luiza Cernadas
Maria Luiza Cernadas
CFCindy S Fernandes
Cindy S Fernandes
JSJosé Luís Santos
José Luís Santos
This work addresses the historical development of techniques and methodologies oriented to the measurement of the internal diameter of transparent tubes since the original contributions of Anderson and Barr published in 1923 in the first issue of Measurement Science and Technology. The progresses on this field are summarized and highlighted the emergence and significance of the measurement approaches supported by the optical fiber.