Ordinary Portland Cement is the most widely used binder in the construction sector; however, a very high carbon footprint is associated with its production process. Consequently, more sustainable alternative construction materials are being investigated, namely, one-part alkali activated materials (AAMs). In this work, waste-based one-part AAMs binders were developed using only a blast furnace slag, as the solid precursor, and sodium metasilicate, as the solid activator. For the first time, mortars in which the commercial sand was replaced by two exhausted sands from biomass boilers (CA and CT) were developed. Firstly, the characterization of the slag and sands (aggregates) was performed. After, the AAMs fresh and hardened state properties were evaluated, being the characterization complemented by FTIR and microstructural analysis. The binder and the mortars prepared with commercial sand presented high compressive strength values after 28 days of curing-56 MPa and 79 MPa, respectively. The mortars developed with exhausted sands exhibit outstanding compressive strength values, 86 and 70 MPa for CT and CA, respectively, and the other material’s properties were not affected. Consequently, this work proved that high compressive strength waste-based one-part AAMs mortars can be produced and that it is feasible to use another waste as aggregate in the mortar’s formulations: the exhausted sands from biomass boilers.
The immobilization of hazardous wastes in ordinary Portland cement (OPC)-based materials has been widely studied and implemented. OPC-based materials have a high carbon footprint associated with their production and geopolymer materials are a sustainable and eco-friendly alternative. Therefore, this work aimed to immobilize two hazardous industrial wastes: copper wastewater sludge and phosphogypsum in one-part geopolymer materials. For that purpose, the precursor was partially substituted by these wastes (5, 10 and 20 wt.%) in the formulations. The geopolymer fresh and hardened state properties were evaluated, and the immobilisation of pollutants was determined through leaching tests. In phosphogypsum pastes (PG5, PG10 and PG20) it was observed that the compressive strength decreased with the increase in its amount, varying between 67 MPa and 19 MPa. In copper sludge pastes, the compressive strength of the specimens (CWS5 and CWS10) reached ~50 MPa. The mortars, MPG10 and MCWSs10, had compressive strengths of 13 MPa and 21 MPa, respectively. Leaching tests showed that pastes and mortars immobilise the hazardous species of the wastes, except for As from copper sludge, whose the best result was found in the compact paste (CWSs10) that leached 2 mg/kg of As. Results suggest that optimized compositions are suitable for the construction sector.
The demand for products derived from the pulp and paper industry has been increasing over the past years and is projected to further increase over the coming decades. Although being one of Portugal’s most relevant industrial activities, contributing to nearly 2.3% of the GDP, this sector is known to generate a variety of wastes including fly ashes, exhausted bed sands, green liquor dregs, grits, lime muds, biological and pulp and paper mill sludges, which have been mostly disposed of in landfills. This strategy is not aligned with the circular economy vision, and therefore it is imperative to develop new recycling routes for the different waste streams. This scenario has driven a significant research effort in the attempt to design sustainable recycling alternatives for the distinct wastes. This study summarizes the investigations focusing on the valorisation of these wastes in a wide range of applications, including the production of low carbon footprint binders or mortars for the construction sector, but also the production of novel materials for high added-value applications such as wastewater treatment and pH regulation. The present work also highlights the main bottlenecks and future prospects for the studied wastes.
Mill scale (MS) is a iron-rich waste generated in the wire drawing process with high iron content and is still mainly disposed in landfills. The scientific community has been studied its use in other applications such as pigments, concretes, among others. This work aims to study a new added-value application for MS—the development of coloured ceramic pastes. For this purpose, the influence of the added amount (0, 1, 3, 5 and 10 wt.%), the pre-treatment (milling + sieving at 212 μm), the maximum firing temperature (from 1043 to 1165 C) and the type of furnace (laboratory/industrial) were analysed on the sample’s characteristics. A dark grey stoneware product was obtained through the incorporation of 10 wt.% of MS and leaching tests conducted at pilot scale with cups confirmed its immobilization in the ceramic matrix. Furthermore, it was proved that the firing temperature can be reduced by about 100 C without affecting the specimen’s characteristics. This reduction leads to a considerable decrease in the energy consumption upon firing, inducing economic and environmental advantages. Therefore, this work provides a new added-value application for MS and contributes to the reduction of virgin raw materials consumption and development of more sustainable stoneware products.
Electroplating sludge (ES) is currently disposed in landfills and, because of its heavy metal content, poses serious threats to the environment and human health. However, ES might have potential use as colouring agent due to its high concentration of chromium and nickel. Thus, the present work aims at studying the effect of ES incorporation into stoneware bodies. The influence on the final characteristics of fired samples, ES amount and pre-treatment were analysed. It was found that stoneware pastes having uniform brownish hues can be obtained with only 3 wt.% of sieved (<212 μm) ES. The obtained specimens have, once fired, the desired technical and aesthetical characteristics. Further, leaching tests confirmed the immobilisation of hazardous ES species in the ceramic matrix. Hence, it can be concluded that this waste can be used as colouring agent of stoneware pastes substituting commercial pigments and contributing to more sustainable consumption and production in the ceramic sector.