Lower-limb exoskeletons, regardless of their control strategies, have been shown to alter a user’s gait just by the exoskeleton’s own mass and inertia. The characterization of these differences in joint kinematics and kinetics under exoskeleton-like added mass is important for the design of such devices and their control strategies. In this study, 19 young, healthy participants walked overground at self-selected speeds with six added mass conditions and one zero-added-mass condition. The added mass conditions included +2/+4 lb on each shank or thigh or +8/+16 lb on the pelvis. OpenSim-derived lower-limb sagittal-plane kinematics and kinetics were evaluated statistically with both peak analysis and statistical parametric mapping (SPM). The results showed that adding smaller masses (+2/+8 lb) altered some kinematic and kinetic peaks but did not result in many changes across the regions of the gait cycle identified by SPM. In contrast, adding larger masses (+4/+16 lb) showed significant changes within both the peak and SPM analyses. In general, adding larger masses led to kinematic differences at the ankle and knee during early swing, and at the hip throughout the gait cycle, as well as kinetic differences at the ankle during stance. Future exoskeleton designs may implement these characterizations to inform exoskeleton hardware structure and cooperative control strategies.
To improve exoskeleton designs, it is crucial to understand the effects of the placement of such added mass on a broad spectrum of users. Most prior studies on the effects of added mass on gait have analyzed young adults using discrete point analysis. This study quantifies the changes in gait characteristics of young and middle-aged adults in response to added mass across the whole gait cycle using statistical parametric mapping. Fourteen middle-aged and fourteen younger adults walked during 60 s treadmill trials under nine different loading conditions. The conditions represented full-factorial combinations of low (+3.6 lb), medium (+5.4 lb), and high (+10.8 lb) mass amounts at the thighs and pelvis. Joint kinematics, kinetics and muscle activations were evaluated. The young and middle-aged adults had different responses to added mass. Under pelvis loading, middle-aged adults did not adopt the same kinematic responses as younger adults. With thigh loading, middle-aged adults generally increased knee joint muscle activity around heel strike, which could have a negative impact on joint loading. Overall, as age may impact the user’s response to an exoskeleton, designers should aim to include sensors to directly monitor user response and adaptive control approaches that account for these differences.
Joint quasi-stiffness has been often used to inform exoskeleton design. Further understanding of hip quasi-stiffness is needed to design hip exoskeletons. Of interest are wearer responses to walking speed changes with added mass of the exoskeleton. This study analyzed hip quasi-stiffness at 3 walking speed levels and 9 added mass distributions among 13 young and 16 middle-aged adults during mid-stance hip extension and late-stance hip flexion. Compared to young adults, middle-aged adults maintained a higher quasi-stiffness with a smaller range. For a faster walking speed, both age groups increased extension and flexion quasi-stiffness. With mass evenly distributed on the pelvis and thighs or biased to the pelvis, both groups maintained or increased extension quasi-stiffness. With mass biased to the thighs, middle-aged adults maintained or decreased extension quasi-stiffness while young adults increased it. Young adults decreased flexion quasi-stiffness with added mass but not in any generalizable pattern with mass amounts or distributions. Conversely, middle-aged adults maintained or decreased flexion quasi-stiffness with even distribution on the pelvis and thighs or biased to the pelvis, while no change occurred if biased to the thighs. In conclusion, these results can guide the design of a hip exoskeleton’s size and mass distribution according to the intended user’s age.
Scaffolding learning and incorporating hands-on activities are proven pedagogical techniques that improve student engagement. A growing movement within engineering education has been to educate beyond the technical skills and foster an improvement in students’ entrepreneurial mindset. A modified version of a validated self-efficacy tool is used here to assess the impact that scaffolding and hands-on activities within a Mechatronics course have on developing the three student learning outcomes associated with the Kern Entrepreneurial Engineering Network's entrepreneurial mindset: “curiosity,” “connections,” and “creating value” (3Cs). A total of 229 students were considered in this study. Presurveys and postsurveys were used to collect self-efficacy ratings for confidence, success, motivation, and anxiety with respect to each of the 3Cs. Additionally, for comparisons a baseline behavioral tool was assessed along with students self-reported prior experiences relevant to the course and overall time spent on course activities. The group was split into high-performers and low-performers for the purpose of analysis. For all 3Cs, aspects of student perceived confidence and success significantly increased between the presurveys and postsurveys for the entire group. However, student perceived motivation was not significantly improved for any of the 3Cs. Interestingly for “connections,” student perceived anxiety decreased only for the high-performing group. This study suggests that changes in these 3Cs can be identified within a single course when subaspects of the mindset are considered.