A Highly Efficient Aeroelastic Optimization Method Based on a Surrogate Model Kriging;back propagation neural networks;genetic algorithms;improved particle swarm optimization; This paper presents a highly efficient aeroelastic optimization method based on a surrogate model; the model is verified by considering the case of a high-aspect-ratio composite wing. Optimization frameworks using the Kriging model and genetic algorithm (GA), the Kriging model and improved particle swarm optimization (IPSO), and the back propagation neural network model (BP) and IPSO are presented. The feasibility of the method is verified, as the model can improve the optimization efficiency while also satisfying the engineering requirements. Moreover, the effects of the number of design variables and number of constraints on the optimization efficiency and objective function are analysed in detail. The accuracy of two surrogate models in aeroelastic optimization is also compared. The Kriging model is constructed more conveniently, and its predictive accuracy of the aeroelastic responses also satisfies the engineering requirements. According to the case of a high-aspect-ratio composite wing, the GA is better at global optimization.
Due to the complexity and particularity of the joined wing layout, traditional design methods for the global stiffness of a high-aspect wing are not applicable for a joined wing. Herein, a beam-frame model and a three-dimensional wing-box model are built to solve the global stiffness aeroelastic optimization design problem for a joined wing. The goal is to minimize the weight, and the constraints are the overall aeroelastic requirements. Based on a genetic algorithm, two methods for the beam-frame model and one method for the three-dimensional model are used for comparative analysis. The results show that the optimization method for a diagonal beam section and the optimization method for an exponential/linear combination function fit are adequate for optimizing and designating the joined wing global stiffness. The distributions obtained using the two methods have good consistency and are similar to the distribution of the three-dimensional model. The stiffness distribution data and the beam section parameters can be converted from each other, which is convenient for redesigning the structure parameters using the stiffness distribution data, and is valuable for engineering applications.
Hypersonic vehicles are susceptible to considerable aerodynamic heating and noticeable aerothermoelastic effects during flight due to their high speeds. Functionally graded materials (FGMs), which enable continuous changes in material properties by varying the ratio of different materials, provide both thermal protection and load-bearing capabilities. Therefore, they are widely used in thermal protection structures for hypersonic vehicles. In this work, the aerothermoelastic behaviors of functionally graded (FG) plates under arbitrary temperature fields are analyzed via a semianalytical method. This research develops a method considering the influence of thermal loading, specifically the decrease in stiffness due to thermal stresses, as well as the correlation between material properties and temperatures under arbitrary temperature fields, based on Ritz’s method. The classical plate theory, von–Karman’s large defection plate theory and piston theory are employed to formulate the strain energy, kinetic energy and external work functions of the system. This paper presents a novel analysis of static aerothermoelasticity of FG plates, in addition to the linear/nonlinear flutter under arbitrary temperature fields, such as uniform, linear and nonlinear temperature fields. In addition, the effects of the volume fraction index, dynamic pressure, and temperature increase on the aerothermoelastic characteristics of FG plates are analyzed.
The increasing structural flexibility of large aircraft leads to significant aeroelastic effects. More efficient topology optimization techniques are required for the design to further take advantage of aeroelasticity and obtain lightweight structures. This paper proposes a moving boundary meshfree topology optimization that combines the Galerkin method of weighted residuals and non-uniform rational B-splines (NURBS). The solution domain is described by the control points of NURBS and its property is calculated adaptively with an integration subtraction technique. The minimal compliance is searched for using the globally convergent method of moving asymptotes (GCMMA) by designing the locations of control points as subject to volume and flux constraints. The method is first applied to a typical two-dimensional design example with symmetric boundary conditions. The results show that the shape constraints can be conveniently applied, and smoother boundaries are obtained with fewer parameters. Then, a three-dimensional wing structure with asymmetric boundary conditions is optimized. A three-dimensional flight load that combines the high-order-panel and meshfree methods is employed to calculate the elastic loads and update asymmetric external loads during the optimization process. The designed wing satisfies engineering requirements and the presented method can solve the practical topology optimization problems of three-dimensional structures.
The increasing demands for travelling comfort and reduction of carbon dioxide emissions have been considered substantially in the stage of conceptual aircraft design. However, the design of a modern aircraft is a multidisciplinary process, which requires the coordination of information from several specific disciplines, such as structures, aerodynamics, control, etc. To address this problem with adequate accuracy, the multidisciplinary analysis and optimization (MAO) method is usually applied as a systematic and robust approach to solve such complex design issues arising from industries. Since MAO method is tedious and computationally expensive, genetic programming (GP)-based metamodeling techniques incorporating MAO are proposed as an effective approach to minimize the wing stiffness of a large aircraft subject to aerodynamic, aeroelastic and stability constraints in the conceptual design phase. Based on the linear small-disturbance theory, the state-space equation is employed for stability analysis. In the process of multidisciplinary analysis, aeroelastic response simulations are performed using Nastran. To construct metamodels representing the responses of the interests with high accuracy as well as less computational burden, optimal Latin hypercube design of experiments (DoE) is applied to determine the optimized distribution of sampling points. Following that, parametric optimization is carried out on metamodels to obtain the optimal wing geometry shape, elastic axis positions and stiffness distribution, and then the solution is verified by finite element simulations. Finally, the superiority of the GP-based metamodel technique over genetic algorithm is demonstrated by multidisciplinary design optimization of a representative beam-frame wing structure in terms of accuracy and efficiency. The results also show that GP metamodel-based strategy for solving MAO problems can provide valuable insights to tailoring parameters for the effective design of a large aircraft in the conceptual phase.