A novel vortex-induced piezoelectric energy converter (VIPEC) is presented in this paper to harvest ocean kinetic energy in the underwater environment. The converter consists of a circular cylinder, a pivoted plate attached to the tail of the cylinder, several piezoelectric patches and a storage circuit. Vortex-induced pressure difference acts on the plate and drives the plate to squeeze piezo patches to convert fluid dynamic energy into electric energy. The output voltage is derived from the piezoelectric constitutive equation with fluid forces. In order to evaluate the performance of the VIPEC, two-dimensional computational fluid dynamics (CFD) simulations based on the Reynolds averaged Navier–Stokes (RANS) equation and the shear stress transport (SST) k- turbulence model are conducted. The CFD method is firstly verified for different grid resolutions and time steps, and then validated using simulation and experimental data. The influences of the plate length and flow velocity on the wake structure, the driving force and the performance of the VIPEC are investigated. The results reveal that different parameters reach their peaks at different plate lengths, and the converter has a maximal output voltage of mV in a specified condition and the maximal power density reaches 0.035 W/m with a resistance load of 10 M . The influence of the simulated subcritical Reynolds number on the driving force is not noticeable. The simulation results also demonstrate the feasibility of this device.
Unmanned underwater vehicles (UUV) face maneuverability and rapidity challenges when they are applied for detecting and repairing submarine oil and gas pipelines, and fiber cables near the seabed. This research establishes numerical models of the bare UUV and self-propelled UUV near the seabed using the computational fluid dynamics (CFD) method. The effect of dimensionless distance Hd and on the hydrodynamic performance of the vehicle and the interaction between the hull and the propeller is investigated. The range of Hd is 1.5D–10D, and the is 9.97 × 105~7.98 × 106. Findings indicate that: (1) There is an obvious strong coupling between the hydrodynamic performance of the bare UUV and Hd. With the increase of Hd, the hydrodynamic performance such as , the absolute value of and decreases continuously and finally tends to be stable. The absolute values of and increase with the increase of . The change trend of is opposite to that of . (2) The variation trend of hydrodynamic performance of the self-propelled UUV with Hd is consistent with those of the bare UUV. Additionally, it increases to some extent, respectively, compared with the bare UUV. (3) The self-propelled characteristics such as , , and are weakly related to Hd. The and increase with the increasing of , while and decrease with the increasing of .
This paper presents an optimization method for the design of the layout of an autonomous underwater vehicles (AUV) fleet to minimize the drag force. The layout of the AUV fleet is defined by two nondimensional parameters. Firstly, three-dimensional computational fluid dynamics (CFD) simulations are performed on the fleets with different layout parameters and detailed information on the hydrodynamic forces and flow structures around the AUVs is obtained. Then, based on the CFD data, a back-propagation neural network (BPNN) method is used to describe the relationship between the layout parameters and the drag of the fleet. Finally, a genetic algorithm (GA) is chosen to obtain the optimal layout parameters which correspond to the minimum drag. The optimization results show that the total drag of the AUV fleet can be reduced by 12% when the follower AUV is located directly behind the leader AUV and the drag of the follower AUV can be reduced by 66% when it is by the side of the leader AUV.
The vortex-induced vibration (VIV) suppression of a circular cylinder with the axial-slats is numerically investigated using the computational fluid dynamics (CFD) method for Reynolds number range of 8.0 × 103–5.6 × 104. The two-dimensional unsteady Reynolds averaged Navier–Stokes (RANS) equations and Shear-Stress-Transport (SST) turbulence model are used to calculate the flow around the cylinder in ANSYS Fluent. The Newmark-β method is used to evaluate structural dynamics. The amplitude response, frequency response and vortex pattern are discussed. The suppression effect of the axial-slats is the best when the gap ratio is 0.10 and the coverage ratio is 30%. Based on the VIV response, the whole VIV response region is divided into four regions (Region I, Region II, Region III and Region IV). The frequency ratio of isolated cylinder jumps between region II and region III. However, the frequency ratio jumps between region I and region II for a cylinder with the axial-slats. The axial-slats destroy the original vortex and make the vortex easier to separate. The online amplitude ratio is almost completely suppressed, and the cross-flow amplitude ratio is significantly suppressed.
5 February 2018 in Advances in Mechanical Engineering
The limited battery energy restricts the underwater operation duration of the underwater moored platforms. In this article, a horizontal axis ocean current turbine is conceptually designed to produce power for the underwater moored platforms and extend their operational durations. As part of the development of the horizontal axis ocean current turbine, a three-dimensional dynamic model of the system is proposed. The underwater moored platform is modeled as a rigid body with the Newton–Euler method and the cable is modeled with a lumped mass method. Motion simulations are then performed to evaluate the motion performance of the moored system under different operation conditions. The influences of the net buoyancy and the ocean current velocity on the motion of the underwater moored platform are investigated. The simulation results show that the underwater moored platform oscillates in water due to the periodically changed rotor forces. The system has a higher motion stability at a higher net buoyancy, with a smaller horizontal offset and a smaller cable inclination angle. The motion stability of the system also increases with the decreased ocean current velocity.