Since the concept of sustainable development enjoys popular support in the 21st century, various kinds of unconventional materials were introduced for soil improvement in the past few decades to replace the traditional materials like concrete and lime. This paper compared nanomaterials with other three kinds of representative unconventional materials to demonstrate its superiority in soil treatment. The other three kinds of unconventional materials include microbially induced calcite precipitation (MICP), recycled tire and environmental fiber. Nanomaterial and MICP have a comprehensive effect on soil reinforcement, since they can improve shear strength, adjust permeability, resist liquefaction and purify the environment. Recycled tire and environmental fibers are granular materials that are mostly adopted to reinforce reconstituted soil. The reinforcement mechanisms and effects of these four kinds of unconventional materials are discussed in detail, and their price/performance ratios are calculated to make an evaluation about their market application prospects. It can be seen that nanomaterials have promising prospects. Colloidal silica, bentonite and laponite present a satisfactory effect on liquefaction mitigation for sandy foundation, and carbon nanotube has an aptitude for unconfined compressive strength improvement. Among the investigated nanomaterials, colloidal silica is the closest to scale market application. Despite the advantages of nanomaterials adopted as additives for soil improvement, they are known for unwanted interactions with different biological objects at the cell level. Nevertheless, research on nanomaterials that are adopted for soil improvement are very promising and can intensify the relationship between sustainable development and geotechnical engineering through innovative techniques.
In the booming field of nanotechnology, colloidal silica (CS) has been introduced for ground improvement and liquefaction mitigation. It possesses a great ability to restrain pore pressure generation during seismic events by using an innovative stabilization technique, with the advantages of being a cost-effective, low disturbance, and environmentally friendly method. This paper firstly introduces molecular structures and some physical properties of CS, which are of great importance in the practical application of CS. Then, evidence that can justify the feasibility of CS transport in loose sand layers is demonstrated, summarizing the crucial factors that determine the rate of CS delivery. Thereafter, four chemical and physical methods that can examine the grouting quality are summed and appraised. Silica content and chloride ion concentration are two effective indicators recommended in this paper to judge CS converge. Finally, the evidence from the elemental tests, model tests, and field tests is reviewed in order to demonstrate CS’s ability to inhibit pore water pressure and lower liquefaction risk. Based on the conclusions drawn in previous literature, this paper refines the concept of CS concentration and curing time being the two dominant factors that determine the strengthening effect. The objective of this work is to review CS treatment methodologies and emphasize the critical factors that influence both CS delivery and the ground improving effect. Besides, it also aims to provide references for optimizing the approaches of CS transport and promoting its responsible use in mitigating liquefaction.
21 January 2021 in Advances in Materials Science and Engineering
Gravelly soils are widely adopted as civil construction materials in engineering practice. Although the influence mechanism of fine contents (FCs) on the mechanical behavior of gravelly soils has been emphasized in the previous studies, few discuss the compaction and strength properties concurrently. Besides, FCs of gravelly soils were discussed separately in many cases regardless of the variation in water content. In this study, modified Proctor compaction test and medium‐sized triaxial test were performed to investigate the mechanical properties of gravelly soils containing different magnitudes of fine contents. It is shown that an optimum FC exists for gravelly soils although the value of the optimum FC varies with grading curves of the coarse‐grained portion. By adjusting FC in the gravelly soils, not only could the maximum dry density ρdmax be improved but also the optimum saturation degree Sropt rises significantly, and synchronously, the minimum air void ratio vamin decreases notably. Besides, fine particles are just right to fill with the voids formed by the coarse‐grained skeleton for the optimum FC sample. The soil structure corresponding to the optimum FC status can be termed as a densely filled skeleton structure, which is the densest and most stable. As fine contents increase or decrease from the optimum value, soil structure will loosen and deteriorate the mechanical properties. In addition, the increase in water content has quite different effects on strength properties of gravelly soils with different FCs in a triaxial test due to the opposite effects of pore water softening and negative pore pressure strengthening. Such results are expected to provide guidance for the preparation of gravelly soils in engineering practices.
To investigate the long-term deformation properties of unbound granular materials (UGM) that are ordinarily adopted to construct subgrade for high-speed railway, a series of medium-sized cyclic triaxial tests were performed to obtain the relationship between permanent strain and loading cycles under different cyclic stress levels. Moreover, DEM analysis was conducted for the samples to reveal the deformation mechanism and verify the strain developing tendency. It is found that the UGM samples present different long-term deformation properties under different cyclic stress levels. As cyclic stress increases, the permanent strain of UGM sample transfers from rapid stabilization to tardy stabilization, then to tardy failure and finally to rapid failure. Furthermore, the exponent in a power law function was selected as the critical indicator of deformation developing tendency. With the exponent obtained precisely in accordance with the strain rate, the deformation tendency can be analyzed quantitatively. Finally, the characteristics of interparticle force chains induced by different cyclic stress levels were obtained by DEM analysis, which provided evidences for the classification of long-term deformation properties of UGM samples. The achievements have guiding significance for the design of subgrade of both ballasted and unballasted high-speed railway.
A series of medium-sized cyclic triaxial tests were performed to investigate the permanent deformation properties of granular materials. The strain rate was then plotted against loading cycles to classify the permanent deformation properties of granular materials under different cyclic stress ratios (CSRs). It was found that (1) the permanent strain rate dεp/dN was linearly correlated with loading cycles N using a double-log coordinate on the condition of CSR < 60%; (2) the deformation tendency factor β, which was extracted from the linear relationship between dεp/dN and N, significantly varied with CSR and, thus, can be adopted to identify the deformation states; (3) β > 1 implying that permanent strain accumulation ceases in limited cycles and corresponds to the plastic shakedown range, while 0 < β ≤ 1 indicates the temporary steady state, corresponding to the plastic creep range; (4) sluggish decrease or remarkable increase in dεp/dN appeared as CSR ≥ 60%, leading to soil collapsed in limited loading cycles and resulting in an incremental collapse range. The new approach was validated by the crushed tuff aggregates and subgrade materials reported previously. It is expected that the new approach will have wider applicability than the traditional one and can provide technical guidance for the design and construction of substructures in roadway and railway engineering.
To investigate the evolving characteristics of plastic deformation for the angular gravels that are used to construct subgrade bed, a laboratory model test is performed with cyclic load applying. Vertical deformation is measured in real time by displacement transducers and further modified to analyze the plastic behavior of model fillings. It can be found that vertical plastic deformation shows quite different developing patterns under the effect of different cyclic amplitudes for a given model. A power function is adopted to describe the relationship between deformation rate and loading times. By analyzing the value of the power exponent and the corresponding developing features of plastic deformation rate, model filling status can be classified into four different zones, i.e., rapid stabilization, tardy stabilization, tardy failure, and rapid failure. Such a classification reveals different developing patterns of plastic deformation and satisfies the design of subgrade bed for ballasted and unballasted railway.