In this article, multiwalled carbon nanotube/natural rubber composites with resistance-strain sensitivity were prepared by solution method, when the electrical percolation threshold of multiwalled carbon nanotube is only ∼3.5 wt%. The mechanical properties and resistance-strain response sensitivity were studied and analyzed systematically. The dispersion of multiwalled carbon nanotubes in the natural rubber matrix was characterized by field-emission scanning electron microscope and X-ray diffractometer. The composite exhibits good deformation sensitivity (gauge factor >27), large strain sensing range (>200%), and high signal stability when multiwalled carbon nanotube content was appropriate. The composite is suited to application in strain monitoring of large deformation structures since the resistance-strain response is more stable when strain exceeds 100%. To understand the mechanism of the resistance-strain response, the ‘shoulder peak’ of resistance-strain curve was researched and explained by the digital image correlation method, and an analytical model was developed when considering the effects of electronic tunneling and hopping in multiwalled carbon nanotube networks. Both experiment and analytical results confirm the break-restructure process of multiwalled carbon nanotube networks under applied strain cause the resistance-strain response. Finally, the practical application of the composite to monitoring strain load of rubber isolation bearing was realized.
The dispersion, electrical conductivities, mechanical properties and resistance–strain response behaviors of multiwalled carbon nanotube (MWCNT)/natural rubber (NR) composites synthesized by the different processing conditions are systematically investigated at both macro- and micro-perspectives. Compared with the solution and flocculation methods, the two roll method produced the best MWCNTs distribution since the materials are mixed by strong shear stress between the two rolls. An excellent segregated conductive network is formed and that a low percolation threshold is obtained (~1 wt.%) by the two roll method. Different from the higher increases in conductivity for the composites obtained by the solution and flocculation methods when the MWCNT content is higher than 3 wt.%, the composite prepared by the two roll method displays obvious improvements in its mechanical properties. In addition, the two roll method promotes good stability, repeatability, and durability along with an ultrahigh sensitivity (GFmax = 974.2) and a large strain range (ε = 109%). The ‘shoulder peak’ phenomenon has not been observed in the composite prepared by the two roll method, confirming its potential for application as a large deformation monitoring sensor. Moreover, a mathematical model is proposed to explain the resistance–strain sensing mechanism.
22 April 2022 in Journal of Applied Polymer Science
Three different blending procedures were used to create multiwalled carbon nanotube (MWCNT)-modified chloroprene rubber (CR)/natural rubber (NR) blended composites (MWCNT/CR–NR). The effects of the blending process on the morphology of the conductive network and interfacial contacts were researched, as well as the resistance–strain response behavior of the composites and the mechanism of composite sensitivity change under different processes. The results show that MWCNT/CR–NR composites have a wide strain range (ε = 300%) and high dynamic resistance–strain response repeatability. Different blending procedures have different effects on the morphology of the conductive network and the interfacial interactions of the composites. If the blending procedures have wider conductive phase spacing and stronger interfacial contacts, the change in the conductive path and tunneling distance occurs more rapidly, and the material has a higher resistance–strain response sensitivity.
In this paper, the effect of WCp particle content (3 and 15 vol.%) and laminate orientation on the mechanical behavior of laminated Cu/WCp/15p and Cu/WCp/3p composites under dynamic impact was investigated using the split Hopkinson pressure bar (SHPB) test. Subsequently, the micro-damage evolution mechanism of the composites was observed by scanning electron microscopy (SEM) and optical microscopy. The results demonstrated that Cu/WCp composites are strain-rate-sensitive, and a significant reinforcing effect of WCp particle content on composite properties was observed. Furthermore, the gradient direction revealed a remarkable effect on the dynamic compressive behavior of functionally gradient materials (FGMs). Microscopic analysis revealed that under the same strain rate, there were no apparent damage characteristics in Cu/WCp/3p, while obvious shear cracks appeared in Cu/WCp/15p. SEM analysis revealed that, in FGM, when the laminate orientation was parallel to the stress wave propagation direction, cracks initiated from one side of Cu/WCp/15p, and then grew through the interface to the other side. A relatively large sliding dislocation was observed at the interlayer interface, and the crack arrested at the Cu/WCp/3p layer. However, although the cracks in FGM also initiated from the side of Cu/WCp/15p, they did not cross the interface, but caused a direct split in the interlayer interface, when the laminate orientation was perpendicular to the stress wave propagation direction.
About Me
Kunming University of Scinece and Technology, Kunming, Yunnan, China.
Kunming University of Scinece and Technology, Kunming, Yunnan, China.