Yong Zhao

Dr. Yong Zhao

Harbin Institute of Technology, Harbin, Heilongjiang, China
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 December 2021 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
YZYong Zhao
Yong Zhao
HYHonghao Yue
Honghao Yue
FYFei Yang
Fei Yang
Jian ZhuJian Zhu
Jian Zhu
The deployer uses a voice coil actuator (VCA) to control precisely the separation velocity of CubeSats with different masses. This article proposes a novel VCA with a new structure of double magnetic circuits featuring high thrust density. Unlike the conventional design, the new design achieves high thrust density by using a new structure of double magnetic circuits to concentrate the magnetic flux in the airgap and alleviate the magnetic saturation in the yoke. An improved equivalent magnetic circuit is developed to reveal the performance improvement of the novel VCA. The electromagnetic characteristics of the new VCA are investigated and compared with the conventional counterparts by finite element analysis and experimental tests. One VCA deployer prototype has been fabricated and testedexperimentally to validate the thrust density and separation characteristics.

18 March 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
DQDapeng Quan
Dapeng Quan
CHCaiting He
Caiting He
CLChenyuan Li
Chenyuan Li
ZZZeming Zhao
Zeming Zhao
XYXiaoze Yang
Xiaoze Yang
HWHongtao Wu
Hongtao Wu
Aiming at the defects of long axial size and low torque density of the existing radial flux permanent magnet motor, this paper proposes an axial flux permanent magnet synchronous motor (AFPMM) with a double-stator and single-rotor structure based on the design requirements of the motor for mechanical dogs’ electric drive joints. The finite element method is employed to evaluate the static magnetic field, load characteristics, and associated losses. The analysis indicates that the average magnetic flux density in the air gap reaches approximately 0.95 T, with a rated torque of around 2.72 N.m, a peak torque of 7.6 N.m, and an efficiency of approximately 87.73%. The electromagnetic torque model is developed using the Maxwell tensor method, allowing for the effects of critical structural parameters on torque to be investigated. By optimizing the design for torque density, an improvement of nearly 20% is achieved. A prototype was fabricated and tested, demonstrating good agreement between simulation and experimental results. This research introduces a novel approach for designing axial flux motors with high torque and power densities.

5 August 2020 in Sensors
Verified
Journal Article
Open access
PDF file
FYfei yang
fei yang
YZYong Zhao
Yong Zhao
XMXingke Mu
Xingke Mu
ZWZhang Wenqiao
Zhang Wenqiao
LJLingtong Jiang
Lingtong Jiang
RLRongqiang Liu
Rongqiang Liu
The modular magnetic suspension platform depends on multi degree of freedom of Lorentz force actuators for large bearing capacity, high precision positioning and structure miniaturization. To achieve the integration of vertical driving force and horizontal driving force, a novel 2- (two degrees-of-freedom) DOF Lorentz force actuator is developed by designing the pose of the windings and permanent magnets (PMs). The structure and the working principle are introduced. The electromagnetic force mathematical model is established by the equivalent magnetic circuit method to analyze the coupling of magnetic flux. The distribution characteristics of magnetic flux density are analyzed by the finite-element method (FEM). It is found that the coupling of the magnetic flux and the large magnetic field gradient severely reduce the uniformity of the air-gap magnetic field. The electromagnetic force characteristic is investigated by FEM and measurement experiments. The difference between FEM and experiment results is within 10%. The reasons of driving force fluctuation are explained based on the distribution of air-gap magnetic field. The actuator performance are compared under the sliding mode control algorithm and PID control algorithm and the positioning accuracy is 20 μm and 15 μm respectively. Compared with the similar configuration, the motion range and force coefficient of the Lorentz force actuator in this paper are larger. It has a certain guiding significance on the structure design of the multi degree of freed Lorentz force actuator.

14 February 2024 in Biomimetics
Verified
Journal Article
Open access
PDF file
JWJun Wu
Jun Wu
YSYizhang Sun
Yizhang Sun
HYHonghao Yue
Honghao Yue
JYJunyi Yang
Junyi Yang
FYfei yang
fei yang
YZYong Zhao
Yong Zhao
Aerial recovery and redeployment can effectively increase the operating radius and the endurance of unmanned aerial vehicles (UAVs). However, the challenge lies in the effect of the aerodynamic force on the recovery system, and the existing road-based and sea-based UAV recovery methods are no longer applicable. Inspired by the predatory behavior of net-casting spiders, this study introduces a cable-driven parallel robot (CDPR) for UAV aerial recovery, which utilizes an end-effector camera to detect the UAV’s flight trajectory, and the CDPR dynamically adjusts its spatial position to intercept and recover the UAV. This paper establishes a comprehensive cable model, simultaneously considering the elasticity, mass, and aerodynamic force, and the static equilibrium equation for the CDPR is derived. The effects of the aerodynamic force and cable tension on the spatial configuration of the cable are analyzed. Numerical computations yield the CDPR’s end-effector position error and cable-driven power consumption at discrete spatial points, and the results show that the position error decreases but the power consumption increases with the increase in the cable tension lower limit (CTLL). To improve the comprehensive performance of the recovery system, a multi-objective optimization method is proposed, considering the error distribution, power consumption distribution, and safety distance. The optimized CTLL and interception space position coordinates are determined through simulation, and comparative analysis with the initial condition indicates an 83% reduction in error, a 62.3% decrease in power consumption, and a 1.2 m increase in safety distance. This paper proposes a new design for a UAV aerial recovery system, and the analysis lays the groundwork for future research.

14 August 2022 in Aerospace
Verified
Journal Article
Open access
PDF file
YZYong Zhao
Yong Zhao
QZQingguang Zhao
Qingguang Zhao
FYfei yang
fei yang
HYHonghao Yue
Honghao Yue
XYXiaoze Yang
Xiaoze Yang
HLHuaiyu Li
Huaiyu Li
The launch method of one arrow with multiple satellites can greatly shorten the time for constellation networking and improve the deployment efficiency. A new compression and separation device with a four-bar perimeter arrangement is proposed for multi-satellite compaction and in-orbit release. A compression device with gap elimination is designed to implement the reliable compaction of stacked flat satellites. An electromagnetic separation device is proposed to achieve the fast, low-interference release of multi-satellites. The dynamic model with flexible guide bars is established. The separation characteristics of multiple satellites are analyzed by the kinematic simulation. The prototype is developed, and the related experiment is implemented. The results show that the four-guide-bar-edge arrangement scheme with a gap elimination device achieves reliable locking and fast separation under a vibration environment. The dynamic separation characteristics of satellites are investigated by the air floatation experiments. The results show that a stable separation speed and low disturbance angular velocity are achieved under 10% spring error.

20 January 2022 in Sensors
Verified
Journal Article
Open access
PDF file
FYfei yang
fei yang
YZYong Zhao
Yong Zhao
HLHuaiyu Li
Huaiyu Li
XMXingke Mu
Xingke Mu
ZWZhang Wenqiao
Zhang Wenqiao
RLRongqiang Liu
Rongqiang Liu
For large bearing capacity and low current consumption of the magnetic suspension platform, a 2-DOF electromagnetic actuator with a new structure of halbach array is proposed to improve driving force coefficients. The structure and the working principle are introduced. An accurate sub domain model of the new structure is established to accurately and rapidly calculate the magnetic field distribution for obtaining the parameters and performance of the electromagnetic actuators. The analytical model results are verified by the finite element method. The force/torque model of the magnetic suspension platform is established based on the proposed 2-DOF electromagnetic actuator. Three position-sensitive detectors and six accelerometers are applied to perceive in real time the posture and vibration acceleration of the platform, respectively. Their hardware information is introduced and measurement models are established based on the layout. Finally, the electromagnetic characteristics of the proposed actuator are investigated and compared with the conventional counterpart by finite element analysis. The results show that the average magnetic field, 0.432 T, horizontal and vertical force coefficient, 92.3 N/A and 30.95 N/A, and torque in x and z direction, 3.61 N·m and 8.49 N·m, of the proposed actuator are larger than those of the conventional one.