yusuf fedai

Dr. yusuf fedai

industrial engeneering, Osmaniye Korkut Ata University, Osmaniye, Turkey (Türkiye)
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 September 2023 in Processes
Verified
Journal Article
Open access
PDF file
yusuf fedaiyusuf fedai
yusuf fedai
Many problems such as delamination, cracking, fiber tearing, ovality, and surface roughness are encountered in the drilling of glass-fiber-reinforced composite (GFRP) materials. In this study, the percentage of multi-walled carbon nano tube (MWCNT), cutting tool type, feed rate, and cutting speed were selected as control factors during the drilling of MWCNT-reinforced GFRP nanocomposites. The quality characteristics of the drilling process were determined as surface roughness, delamination, torque, and thrust force. The experiments were carried out in accordance with the Taguchi L27 orthogonal array. The lowest values obtained because of the experiments were Ra = 4.95 µm, Dm = 1.099, T = 14.78 N, and F = 44.24 N, respectively. However, since each of these outputs were obtained from different experimental trials, different multi-criteria decision-making (MCDM) methods were used to optimize all outputs at the same time. First, the criteria were weighted using the fuzzy AHP method, and then the outputs were optimized using multi-criteria decision-making methods (i.e., GRA, WASPAS and VIKOR). Very close optimal ranking was obtained in all three methods. The best results were obtained for Ra = 4.86 µm, Dm = 1.13, T = 55.57 N, and F = 48.00 N. In the next step, the performance values obtained from each MCDM method were re-optimized using the Taguchi S/N ratio method. By comparing between these models, a single optimal condition for drilling is proposed. Accordingly, A2B3C1D1 (Ra = 4.86 µm, Dm = 1.10, T = 17.47 N and F = 48.33 N) for FAHP-GRA and FAHP-WASPAS and A2B3C2D2 (Ra = 5.02 µm, Dm = 1.09, T = 37.19 N and F = 45.01 N) for FAHP-VIKOR were determined as the best performing experiments. Finally, validation tests were conducted to compare the performance of the experiments. As a result, the FAHP-GRA and FAHP-WASPAS optimization with Taguchi S/N gave an unweighted improvement of 82.9% and a weighted improvement of 10.04% compared to the results of the experiment with MCDM. Compared to the results of the experiments with MCDM, S/N FAHP-VIKOR provided an unweighted improvement of 52.75% and a weighted improvement of 8.19%. According to the results obtained, for this study, FAHP-GRA and FAHP-WASPAS are more effective optimization methods than FAHP-VIKOR.

27 March 2018 in Tehnički glasnik
Verified
Journal Article
Open access
PDF file
Gökhan BAŞARGökhan BAŞAR
Gökhan BAŞAR
FKFunda Kahraman
Funda Kahraman
HAHediye KIRLI AKIN
Hediye KIRLI AKIN
yusuf fedaiyusuf fedai
yusuf fedai
In this study, the effect of cutting parameters such as the depth of cut, feed rate, cutting speed and the number of inserts on surface roughness were investigated in the milling of the AISI 4140 steel. The optimal control factors for...

28 June 2018 in Tehnički glasnik
Verified
Journal Article
Open access
PDF file
yusuf fedaiyusuf fedai
yusuf fedai
HAHediye KIRLI AKIN
Hediye KIRLI AKIN
FKFunda Kahraman
Funda Kahraman
Gökhan BAŞARGökhan BAŞAR
Gökhan BAŞAR
In this research, the effect of machining parameters on the various surface roughness characteristics (arithmetic average roughness (Ra), root mean square average roughness (Rq) and average maximum height of the profile (Rz)) in the...

12 October 2023 in Lubricants
Verified
Journal Article
Open access
PDF file
yusuf fedaiyusuf fedai
yusuf fedai
Optimizing input parameters not only improves production efficiency and processing quality but also plays a crucial role in the development of green manufacturing engineering practices. The aim of the present study is to conduct a comparative evaluation of the cutting performance and machinability process during the turning of AISI 4340 steel under different cooling conditions. The study analyzes cutting operations during turning using dry, minimum quantity lubrication, and nano- minimum quantity lubrication. As control parameters in the experiments, three different cooling types, cutting speeds (100, 150, 200 m/min), and feed rate (0.1, 0.15, 0.20 mm/rev) levels were applied. The experimental results show that the optimal output values are found to be Vb = 0.15 mm, Ra = 0.81µm, 88.1 dB for sound intensity and I = 4.18 A for current. Moreover, variance analysis was performed to determine the effects of input parameters on response values. Under dry, minimum quantity lubrication, and nano-minimum quantity lubrication processing conditions, parameters affecting tool wear, surface roughness, current by the motor shaft, and sound level were examined in detail, along with the chip morphology. The responses obtained were optimized according to the Taguchi S/N method. As a result of optimization, it was concluded that the optimum values for cutting conditions were nano-minimum quantity lubrication cooling and V = 100 m/min, f = 0.1 mm/rev cutting. Finally, it was observed that there was a 13% improvement in tool wear, 7% in current, 9% in surface roughness, and 8% in sound intensity compared to the standard conditions. In conclusion, it was determined that nano-minimum quantity lubrication with the lowest level of cutting and feed rate values provided the optimum results.

31 December 2020 in Çukurova Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
Verified
Journal Article
Closed access
PDF file
Gökhan BAŞARGökhan BAŞAR
Gökhan BAŞAR
yusuf fedaiyusuf fedai
yusuf fedai
HAHediye KIRLI AKIN
Hediye KIRLI AKIN
Cam Elyaf Takviyeli Polimer (CETP) kompozitler, diğer malzemelere göre daha üstün özelliklere sahip olmasından dolayı birçok mühendislik uygulamalarında kullanılmaktadır. Bu kompozitlerin montajında delme işlemi yaygın olarak uygulanmaktadır. CETP malzemelerin delinmesinde; yüksek delik yüzey kalitesi ile minimum deformasyon ve itme kuvveti için delme parametrelerinin belirlenmesi oldukça önemlidir. Bu yüzden, delme işlemi sırasında oluşan delik yüzeyi hasarını en aza indirmek için optimum delme koşulları belirlenmelidir. Bu çalışmada, delme işleminde itme kuvveti Taguchi Metodu kullanılarak optimize edilmiştir. Ayrıca, itme kuvvetinin tahminine yönelik matematiksel modeller geliştirilmiştir. Delme parametrelerinin itme kuvveti üzerindeki etki oranları varyans analizi ile belirlenmiştir. Varyans analizine göre itme kuvveti üzerindeki en etkili parametrenin ilerleme olduğu görülmüştür. İtme kuvvetini tahmin etmek için Taguchi Metodu, birinci ve ikinci dereceden regresyon modelleri kullanılmıştır. Elde edilen sonuçlar ile deney sonuçları karşılaştırılmıştır. Ayrıca, üç boyutlu grafikler incelendiğinde, % çok duvarlı karbon nanotüp oranı ve kesme hızı arttıkça itme kuvvetinin azaldığını ve ilerleme arttıkça itme kuvvetinin arttığını göstermiştir.

1 September 2023 in Journal of Engineering Research
Verified
Journal Article
Open access
PDF file
Muhammed OrduMuhammed Ordu
Muhammed Ordu
yusuf fedaiyusuf fedai
yusuf fedai
The aim of this study is to develop a novel decision support system, which has never been developed yet, in order to optimize machining parameters. We combine the three distinct methods: experimental design and analysis, fuzzy data envelopment analysis (DEA) and fuzzy analytical hierarchy process (AHP). Firstly, a full factorial experiment including four factors and three levels is carried out. We take into account cutting speed, feed rate, depth of cut and number of cutting tool inserts as factors. The following three outputs are selected: Material Removal Rate, Machining Time and Surface Roughness. Secondly, a total of 23 experiments are determined as efficient decision making units using fuzzy DEA with super efficiency method. Finally, a fuzzy AHP approach is conducted to rank the efficient experiments among each other. In conclusion, the results show that the Fuzzy DEA-Fuzzy AHP and the Fuzzy DEA with Super Efficiency generate clearly different rankings of experiments and Fuzzy DEA-Fuzzy AHP Approach has outperformed Fuzzy DEA with Super Efficiency Approach. The results highlight the importance of taking into account the expert opinions in the decision making processes.