In coal seam gas (CSG) coproduction wells, due to the different production pressures of CSG production layer at different depths, the interlayer interference in wellbore seriously affects the gas production of a coproduction well. To effectively suppress the interlayer interference of the wellbore, a wellbore pressure distribution method for a two-layer coproduction well is proposed. Based on the analysis of the factors influencing the flow pressure distribution in the wellbore of two-layer coproduction wells, a method of coproduction flow pressure adjustment by regulating the wellhead pressure and the depth of the dynamic fluid level was established in this paper. The results show that wellhead pressure can directly affect the production pressure of two layers. The variation in layer 1 output mainly affects the pressure difference between the wellhead pressure and the pressure at the depth of layer 1, which has little effect on the pressure difference between layer 1 and 2. An increase in gas production from layer 2 would not only cause a pressure increase in layer 1, but also result in a reduction of the production pressure at layer 2. The maximum pressure gradient of the gas section is 0.14 MPa/100 m, and the pressure gradient of the gas–liquid section is 0.53–1.0 MPa/100 m.
9 May 2022 in Computational Intelligence and Neuroscience
Beam pumper is the earliest and most popular rod pumper driven by surface dynamic transmission devices. Drawing on modern theories and methods of industrial model design, the model optimization of beam pumper could promote the diversity, serialization, standardization, generalization, precision balance, and energy reduction of beam pumper design. Therefore, this study tries to optimize the model of beam pumper based on a neural network. Specifically, the system efficiency of beam pumper was decomposed, the surface and downhole working efficiencies were analyzed, and the model optimization flow was explained for beam pumper. Then, a radial basis function (RBF) neural network was established and trained by the sample data on beam pumper model. Besides, the mapping between model parameters and the optimization objective (system efficiency) was constructed. Moreover, the authors summed up the model optimization contents of beam pumper and predicted the relevant parameters of model optimization. The results demonstrate the effectiveness of our model.
Cleaning out the pulverized coal deposited at the bottom of a coalbed methane (CBM) well is key to achieving continuous CBM drainage and prolonging the workover period. In this study, Fluent is used in conjunction with the standard k-ε model and the Eulerian-Eulerian model to simulate and analyse jet erosion of deposited pulverized coal particles. The depth and width of the stable erosion pit that is formed by jet-impacting deposited pulverized coal under different conditions are determined and provide a theoretical basis for the cleanout of pulverized coal in the bottom of a CBM well. In this paper, the three parameters of the jet target distance, nozzle diameter and nozzle outlet flow velocity are selected to perform an orthogonal simulation. The change trends in the depth and width of the scouring pit with time are determined. The results show that jet impacting of deposited pulverized coal can be categorised into four stages, periods of rapid growth, stability, jet swing and dynamic stability. A sensitivity analysis shows that the nozzle outlet flow velocity has the strongest influence on the depth of the scouring pit among the selected parameters. The depth of the jet impact pit can reach the maximum depth at t = 3 s, while the width of the impact pit can reach the maximum after t = 7 s. This can provide key design parameters for CBM well pulverized coal impacting operation. It is of great significance for capacity damage control during CBM well workover operation.
The cylindrical hydrocyclone can be regarded as a special-shaped hydrocyclone comprising entirely cylindrical sections without conical sections, featuring a unique flat-bottom design combined with central discharge, which promotes substantial particle circulation flow in the separation chamber, directly affecting separation performance. A validated TFM model is employed to investigate the flow field and particle motion behavior in the cylindrical hydrocyclone. The results indicate that the distributions of tangential velocity, radial velocity, pressure, and pressure gradient in the cylindrical hydrocyclone are consistent with patterns observed in the conventional hydrocyclone. The flat-bottom design combined with the central discharge configuration of the cylindrical hydrocyclone results in two distinct axial velocity transitions in the bottom region, forming downward axial velocity flow around the air core. Accordingly, particles moving toward the spigot must pass through the internal swirling flow region, facilitating the fine particles entrained by the coarse particles to enter the internal swirling flow, reducing the misplacement of fine particles in the underflow. Simultaneously, coarse particles entrained by the internal swirling flow return to the external swirling flow region under centrifugal force, forming a substantial coarse particle circulation flow. As a result, a mass of coarse particles accumulates in the separation chamber, hindering the centrifugal settling of medium particles and resulting in an enlarged cut size and severe coarse particle misplacement.
The outlet diameter of hydrocyclones is a critical structural parameter that impacts product distribution and separation performance, drawing significant attention. In this paper, the separation efficiency and particle motion behavior in the cylindrical hydrocyclone with varying spigot diameters and vortex finder diameters are systematically analyzed using a TFM model. The numerical results indicate that a larger spigot diameter and a smaller vortex finder diameter reduce the axial velocity and expand the external swirling flow region, while a smaller spigot diameter and a larger vortex finder diameter enhance the particle circulation flow ratio and the coarse particle circulation flow proportion, thereby increasing the cut size. Slightly reducing the spigot diameter and increasing the vortex finder diameter enhances the separation accuracy. Nevertheless, for Du = 0.075 D and Do ≥ 0.4 D, the recovery rate in the underflow remains below 50% for all particle sizes, exhibiting severe particle misplacement and loss of separation efficiency. For Du = 0.125 D, the reduction in coarse particle misplacement in the overflow is attributed to the abrupt changes in the coarse particle circulation flow proportion and medium particle circulation flow proportion. Generally, an appropriate coarse particle circulation flow proportion in the cylindrical hydrocyclone is beneficial for alleviating particle misplacement and improving separation accuracy.