Xinxin Guo

Mr. Xinxin Guo

Southwest Jiaotong University

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2019 in Construction and Building Materials
Verified
Journal Article
Closed access
BWBo Wang
Bo Wang
XGXinxin Guo
Xinxin Guo
HJHui Jin
Hui Jin
FLFuhai Li
Fuhai Li
YSYang Song
Yang Song

1 April 2018 in International Journal of Rock Mechanics and Mining Sciences
Verified
Journal Article
Closed access
BWBo Wang
Bo Wang
XGXinxin Guo
Xinxin Guo
FLFuhai Li
Fuhai Li
DHDinghan Hu
Dinghan Hu
YJYi Jia
Yi Jia

22 September 2019 in Sensors
Verified
Journal Article
Open access
PDF file
XGXinxin Guo
Xinxin Guo
BWBo Wang
Bo Wang
ZMZhenwang Ma
Zhenwang Ma
ZWZhenyu Wang
Zhenyu Wang
Fiber Bragg grating (FBG) sensors, which can accurately measure strain, can be integrated with rock bolts with small fingerprints. In this paper, according to the force mechanism of prestressed anchor and non-prestressed anchor, different loading modes were designed, named active loading mode and passive loading mode. Then, FBG technology was used to monitor the axial force variation of prestressed anchor and non-prestressed anchor in different loading modes. Based on the test results, it is found that when the anchoring force is relatively small (<35 kN), prestressed anchors need to be tested by active loading mode, and non-prestressed anchors need to be tested by passive loading mode. For the prestressed anchor, the force condition of the bolt-shaft was similar to that of the two-force bar, and the axial force of the bolt-shaft was nearly the same along its entire length. Taking the applied load as the reference, the change rate of the axial force of the bolt-shaft was less than 10%. For non-prestressed anchor, due to the plate, there is a certain area surrounding the plate where the axial force of the bolt-shaft was greatly influenced. With applied loads of less than 15 kN, the change rate of the axial force on FBG1 was greater than 10%. With applied loads of greater than 20 kN, this was less than 10%. In this area, influenced by the plate, the axial force of the bolt-shaft increases, and as the applied load of the pullout test increases, the influence decreases.

5 May 2025 in Scientific Reports
Verified
Journal Article
Open access
PDF file
RWRui Wang
Rui Wang
RCRuiqi Chen
Ruiqi Chen
HYHao Yan
Hao Yan
XGXinxin Guo
Xinxin Guo
This study created the C//Sim attention mechanism employing the parallel connection of the CA attention mechanism and the SimAm attention mechanism to detect cracks in lightweight concrete. MobileNetV3 was improved using the above method, and a lightweight concrete crack recognition model, MobileNetV3-C//Sim, was established. To validate the model’s practicality, this paper has been tested on self-built and public datasets. The improved model performs higher accuracy, recall, precision, and F1 values than Mobilenetv3 in both datasets, with increases of 0.44–0.69% and 0.46–0.89% for the binary and multi classification tasks, respectively. For the CA attention mechanism, SimAm attention mechanism, and ablation tests with different combinations of each other showed that the parallel connection combination was superior to the single-type, front-to-back concatenation combination. In noise testing with different attention mechanisms, the C//Sim reduction is the smallest. It is verified to have better noise immunity and robustness. Regarding the number of model parameters, the proposed method involves only 2.90 M, which is 30.17% less than that of MobileNetV3. The method can provide a model reference for further concrete crack lightweight identification research.

29 August 2024 in Scientific Reports
Verified
Journal Article
Open access
PDF file
RWRui Wang
Rui Wang
RCRui-Qi Chen
Rui-Qi Chen
XGXinxin Guo
Xinxin Guo
JLJia-Xuan Liu
Jia-Xuan Liu
HYHai-Ying Yu
Hai-Ying Yu
Cracks are a common problem in concrete surfaces. With the continuous optimization of machine vision-based inspection systems, effective crack detection and recognition is the core of the entire system. In this study, support vector machine (SVM) was used to distinguish cracks from other regions. To complete the recognition system of the SVM, a framework consisting of an image processing and recognition model was proposed. An algorithm combining the Prewitt operator with the Otsu threshold was proposed for image segmentation. The binary image processed by the new algorithm combined with mathematical morphology can result in a more complete crack zone and fewer interference regions. After the initial parameter extraction, most of the impurity areas were screened by preliminary discrimination, removing 99% of the impurities. This processing step ensured the balance and effectiveness of the samples. To establish an automatic identification model based on SVM with a radial basis function, compactness, occupancy rate, and length–width ratio were selected as input parameters after comparing these three features with all six features of the crack. The recognition accuracy of this system reaches 97.14%, demonstrating that the proposed method is effective and satisfies practical requirements.

23 February 2024 in Rock Mechanics and Rock Engineering
Verified
Journal Article
Closed access
PDF file
BWBo Wang
Bo Wang
ZWZhenyu Wang
Zhenyu Wang
XGXinxin Guo
Xinxin Guo
JDJie Dong
Jie Dong
ZWZhijiao Wang
Zhijiao Wang