Zoltán Weltsch

Dr. Zoltán Weltsch

Széchenyi István University, Győr, Győr-Moson-Sopron, Hungary
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 March 2021 in Polymers
Verified
Journal Article
Open access
PDF file
MBMiklós Berczeli
Miklós Berczeli
Zoltán WeltschZoltán Weltsch
Zoltán Weltsch
The development of bonding technology and coating technologies require the use of modern materials and topologies for the demanding effect and modification of their wetting properties. For the industry, a process modification process that can be integrated into a process is the atmospheric pressure of air operation plasma surface treatment. This can be classified and evaluated based on the wettability, which has a significant impact on the adhesive force. The aim is to improve the wetting properties and to find the relationship between plasma treatment parameters, wetting, and adhesion. High Impact PolyStyrene (HIPS) was used as an experimental material, and then the plasma treatment can be treated with various adjustable parameters. The effect of plasma parameters on surface roughness, wetting contact angle, and using Fowkes theory of the surface energy have been investigated. Seven different plasma jet treatment distances were tested, combined with 5 scan speeds. Samples with the best plasma parameters were prepared from 25 mm × 25 mm overlapping adhesive joints using acrylic/cyanoacrylate. The possibility of creating a completely hydrophilic surface was achieved, where the untreated wetting edge angle decreased from 88.2° to 0° for distilled water and from 62.7° to 0° in the case of ethylene glycol. The bonding strength of High Impact PolyStyrene was increased by plasma treatment by 297%.

5 July 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
BÁBalázs Ádám
Balázs Ádám
Zoltán WeltschZoltán Weltsch
Zoltán Weltsch
Polylactic acid (PLA) is one of the most promising biopolymers often used as a raw material in 3D printing in many industrial areas. It has good mechanical properties, is characterized by high strength and stiffness, but unfortunately, it has some disadvantages; one is brittleness, and the other is slow crystallization. Amounts of 1–5% SEBS (styrene-ethylene-butylene-styrene) thermoplastic elastomer were blended into the PLA and the thermal and mechanical properties were investigated. DSC (Differential Scanning Calorimetry) measurements on the filaments have shown that SEBS increases the initial temperature of crystallization, thereby acting as a nucleating agent. The cooling rate of 3D printing, on the other hand, is too fast for PLA, so printed specimens behave almost amorphously. The presence of SEBS increases the impact strength, neck formation appears during the tensile test, and in the bending test, the mixture either suffers partial fracture or only bends without fracture. Samples containing 1% SEBS were selected for further analysis, mixed with 0.06 and 0.1% carbon nanotubes (CNTs), and tested for thermal and mechanical properties. As a result of CNTs, another peak appeared on the DSC curve in addition to the original single-peak crystallization, and the specimens previously completely broken in the mechanical tests suffered partial fractures, and the partially fractured pieces almost completely regained their original shape at the end of the test.

1 December 2022 in Polymers
Verified
Journal Article
Open access
PDF file
Attila BataAttila Bata
Attila Bata
DNDorottya Nagy
Dorottya Nagy
Zoltán WeltschZoltán Weltsch
Zoltán Weltsch
In this research the effect of physical recycling on the mechanical, thermal, and rheological properties of polypropylene (PP)/multiwalled carbon nanotube (MWCNT) was investigated. After melt homogenization by extrusion, specimens were injection moulded with 0.1 and 0.5 wt% MWCNT content. The recycling process was simulated by multiple grinding and re-moulding, then we compared the behavior of original and recycled PP/MWCNT composites. Differential scanning calorimetry (DSC) measurements proved that MWCNT had double the effect on the morphology of the PP matrix: on the one hand nucleating effect can be detected because 0.5 wt% MWCNT increased the onset temperature of crystallization by 10 °C, compared to the basic PP material; on the other hand, the crystalline fraction of the recycled composite materials decreased compared to the original PP material with the same MWCNT content. This resulted in a slight decrease in strength and stiffness but an increase in elongation at break. However, compared to the original unreinforced PP reference, even the recycled materials have better properties. The mechanical test results showed that recycled PP/MWCNT 0.5 wt% increased the elastic modulus (~15%) and decreased the tensile strain at yield (~10%). However, in the values of tensile stress at yield, relevant difference was not found. It was also shown by oscillatory rheometry that MWCNT had a significant effect on the rheological properties (storage and loss modulus, complex viscosity) of PP compounds in a wide temperature range (190–230 °C).

16 April 2025 in Batteries
Verified
Journal Article
Open access
PDF file
MPMárton Pepó
Márton Pepó
SFSoma Fullér
Soma Fullér
TCTibor Cseke
Tibor Cseke
Zoltán WeltschZoltán Weltsch
Zoltán Weltsch
Standardised battery tests are essential for evaluating the safety, reliability, and performance of modern battery technologies, especially with the rapid emergence of innovations such as solid-state and lithium–sulphur batteries. This review reveals critical shortcomings in current international standards (e.g., IEC, IEEE, SAE), which often do not keep pace with technological developments and are not harmonised across regions, limiting their effectiveness in real-world applications. The paper stresses the need for the continuous review of test protocols through collaboration between researchers, manufacturers, and regulators. A detailed case study of the BYD Dolphin battery demonstrates the practical importance of comprehensive testing in real-world conditions, spanning electrical, thermal, and mechanical ranges. The review concludes that up-to-date, harmonised, and scenario-specific test methods are needed to ensure accurate battery assessment, support global comparability, and enable the safe introduction of next-generation batteries for electric mobility and energy storage. Future work should prioritise operational monitoring, open access data sharing, and the development of sustainability-focused practices such as recycling and reclamation.

13 November 2024 in Energies
Verified
Journal Article
Open access
PDF file
AKAttila Kissa
Attila Kissa
BSBalint Szabo
Balint Szabo
KKKrisztián Kun
Krisztián Kun
Zoltán WeltschZoltán Weltsch
Zoltán Weltsch
This study explores the performance and emissions characteristics of a dual-fuel internal combustion engine operating on a blend of hydrogen and gasoline. This research began with a baseline simulation of a conventional gasoline engine, which was subsequently validated through experimental testing on an AVL testbed. The simulation results closely matched the testbed data, confirming the accuracy of the model, with deviations within 5%. Building on this validated model, a hydrogen–gasoline dual-fuel engine simulation was developed. The predictive simulation revealed an approximately 5% increase in overall engine efficiency at the optimal operating point, primarily due to hydrogen’s combustion properties. Additionally, the injected gasoline mass and CO2 emissions were reduced by around 30% across the RPM range. However, the introduction of hydrogen also resulted in a slight reduction (~10%) in torque, attributed to the lower volumetric efficiency caused by hydrogen displacing intake air. While CO emissions were significantly reduced, NOx emissions nearly doubled due to the higher combustion temperatures associated with hydrogen. This research demonstrates the potential of hydrogen–gasoline dual-fuel systems in reducing carbon emissions, while highlighting the need for further optimization to balance performance with environmental impact.

3 April 2017 in Soldering & Surface Mount Technology
Verified
Journal Article
Closed access
JHJózsef Hlinka
József Hlinka
MBMiklós Berczeli
Miklós Berczeli
GBGábor Buza
Gábor Buza
Zoltán WeltschZoltán Weltsch
Zoltán Weltsch
Purpose: This paper aims to discuss the effect of surface treatment on the wettability between copper and a lead-free solder paste. The industrial applications of laser technologies are increasing constantly. A specific laser treatment can modify the surface energy of copper and affect the wetting properties. Design/methodology/approach: The surfaces of copper plates were treated using an Nd:YAG laser with varying laser powers. After laser surface treatment, wetting experiments were performed between the copper plates and SAC305 lead-free solder paste. The effect of laser treatment on copper surface was analysed using optical microscopy and scanning electron microscopy (SEM). Findings: The experimental results showed that the wetting contact angles changed with the variation in laser power. Furthermore, it means that the surface energy of copper plates was changed by the laser treatment. The results demonstrated that the contact angles also changed when a different soldering paste was used. Originality/value: Previous laser surface treatment can be a possible way to optimize the wettability between solders and substrates and to increase the quality of the soldered joints.