Zhang Zhongke

Dr. Zhang Zhongke

School of Materials Science and Engineering, Lanzhou University of Technology
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2014 in Transactions of Nonferrous Metals Society of China
Verified
Journal Article
Closed access
ZZZhang Zhongke
Zhang Zhongke
XWXi-Jing Wang
Xi-Jing Wang
PWPei-Chung Wang
Pei-Chung Wang
GZGang Zhao
Gang Zhao

1 September 2017 in Metals
Verified
Journal Article
Open access
PDF file
ZZZhang Zhongke
Zhang Zhongke
YYYang Yu
Yang Yu
JZJian-Fei Zhang
Jian-Fei Zhang
XWXijing Wang
Xijing Wang
The corrosion behavior of keyhole-free friction stir spot welded joints of dissimilar 6082 aluminum alloy and DP600 galvanized steel in 3.5% NaCl solution has been investigated by the immersion test and electrochemical analysis. The surface of the aluminum alloy produced exfoliation and pitting corrosion. The pitting occurred seriously on the interface of the 6082 aluminum alloy, but the steel had no corrosion. The corrosion galvanic couples were formed between elements of Si and Fe with a high electrode potential, and Mg and Al with a low electrode potential, around them. Mg and Al elements of Mg2Si and Si-containing solid-solution phase α (Al) preferentially became an anodic dissolution and formed exfoliation corrosion around the Si elements. Fe-rich phase θ (Al3Fe) as the cathode caused corrosion of Mg and formed pitting around Mg-rich phase β (Al3Mg2) as the anode. The sequence of the corrosion resistance of different areas of the joints (with decreasing corrosion resistance) was WNZ (Weld Nugget Zone) > TMAZ (Thermo-mechanically Affected Zone) > BM (Base Metal) > HAZ (Heat-affected Zone). The joints of keyhole-free FSSW (Fiction Stir Spot Welding) of dissimilar 6082 aluminum alloy and DP600 galvanized steel have better corrosion resistance than base metal in 3.5% NaCl solution.

18 June 2019 in Metals
Verified
Journal Article
Open access
PDF file
ZZZhang Zhongke
Zhang Zhongke
YYYu Yang
Yu Yang
HZHuaxia Zhao
Huaxia Zhao
XWXijing Wang
Xijing Wang
This work systematically investigates the interface behavior and impact properties of the keyhole-free friction stir spot welding (FSSW) of a dissimilar metal AA6082-T4 Al alloy and DP600 galvanized steel. The keyhole is eliminated by pin retraction technology. The welding process is in accordance with the welding temperature curve and the maximum temperature of the periphery of the shoulder, measured at about 500 °C. The transition layers were formed at the interface, in which the Al, Fe, and Zn elements form an inhomogeneous diffusion. A cloud cluster-like mechanical mixing of the Al and steel components is formed in the stirring zone. The impact toughness of the specimen with a welding parameter of 1000 rpm is the best. To a certain extent, the factors affecting the impact energy are not the maximum impact load but the maximum impact deformation. The maximum impact deformation directly reflects the post-crack propagation energy, which significantly affects its impact toughness. In addition, the impact fracture showed a mixed ductile and brittle fracture mode with a brittle–ductile transition zone. Most of the impact energy was absorbed by the ductile fracture.

30 October 2020 in Metals
Verified
Journal Article
Open access
PDF file
ZZZhang Zhongke
Zhang Zhongke
XLXuanbai Li
Xuanbai Li
ZZZaolong Zhao
Zaolong Zhao
CJChangming Jiang
Changming Jiang
HZHuaxia Zhao
Huaxia Zhao
The response surface analysis method was used to systematically study the effect of various parameters on the tensile strength of 6082 aluminum alloy friction plug welding (FPW) joints in this work. The fluidity of the joint and microstructure were observed with a metallurgical microscope. Combined with the temperature field and force analysis, the reason why the root of the joint appears as a weak zone was explained. The results showed that the degree of influence on the tensile strength of FPW joints was rotational speed > upsetting speed > welding time. The optimal FPW joint was obtained when the rotational speed was 2254 rpm, the upsetting speed was 2 mm/s, and the welding time was 25 s, so the tensile strength could reach 262.34 MPa. The microstructure of the FPW joint appeared heterogeneous. According to the different plastic metal fluidities of the joint, it could be divided into four areas. The interaction force at the friction interface was not strong at the root of the FPW joint, so the root often becomes the weak area of the FPW joint.

23 September 2020 in Materials
Verified
Journal Article
Open access
PDF file
ZZZhang Zhongke
Zhang Zhongke
YYYu Yang
Yu Yang
HZHuaxia Zhao
Huaxia Zhao
HTHui Tong
Hui Tong
The energy evolution, fatigue life and failure behaviour of dissimilar Al/steel keyhole-free Friction stir spot welding (FSSW) joints were studied under different fatigue loads. The absorption energy of fatigue fracture, the fracture mechanism and the sensitivity of the fatigue limits to the fatigue load parameters were analysed. It was found that the stress ratio R determines the fatigue limit Ff, while the fatigue limit Ff is not sensitive to the loading frequency. The high-frequency fatigue load will increase the displacement deformation μ and fatigue fracture absorption energy Ea of the spot-welded joint, which are larger under asymmetric fatigue loading than those under symmetrical fatigue loading. At the same time, the symmetrical fatigue load can form the steady-state hysteresis loop, while asymmetric fatigue loading cannot, but asymmetric fatigue loading exhibits the displacement increment of fatigue softening. The fracture failure of spot-welded joints is a multiple crack source and the mixed-mode of ductile and brittle fracture mechanism, which exhibits typical fatigue striations in the fatigue fractures.

1 December 2022 in Materials Research Express
Verified
Journal Article
Open access
ZZZhang Zhongke
Zhang Zhongke
SCShusheng Chu
Shusheng Chu
JXJianqiang Xiong
Jianqiang Xiong
CJChangming Jiang
Changming Jiang
XLXuanbai Li
Xuanbai Li
The effect of solid solution temperature on microstructure and mechanical properties of plasma welded nickel-based high temperature alloy Incone l625 was investigated by solid solution treatment (The solid solution temperature range is 950 °C to 1150 °C and the intergroup interval is 50 °C). The results show that after solid solution treatment at 950 °C, chain carbides are precipitated at the austenite grain boundary of the base material. With solid solution temperature increasing, carbon chains dissolve gradually at the grain boundary. When solution temperature is higher than 1050 °C, carbides at the grain boundary completely melt back into the matrix. At the weld, dendritic crystal and Laves phase dissolve with the increase of solid solution temperature. When the solid solution temperature is 1100 °C, the dendritic crystal and Laves phase at the weld completely melt into the matrix and transform into cellular crystals. When the solid solution temperature is increased to 1150 °C, the cellular crystal grows further at the weld. When the solid solution temperature is 1100 °C, the comprehensive mechanical properties of the joint are the best.