The assessment of a TiO₂ vegetal-based dielectric nanofluid has been carried out, and its characteristics and behavior have been tested and compared with a previously tested maghemite nanofluid. The results obtained reflect a similar affectation of the main properties, with a maximal improvement of the breakdown voltage of 33% at 0.5 kg/m³, keeping the thermal conductivity and the viscosity almost constant, especially the first one. This thermal characterization agrees with the results obtained when applying the TiO₂ optimal nanofluid in the cooling of an experimental setup, with a slightly worse performance than the base fluid. Nevertheless, this performance is the opposite to that noticed with the ferrofluid, which was capable of improving the cooling of the transformer and decreasing its temperature. The similarities between the characterizations of both nanofluids, the differences in their cooling performances and their different magnetic natures seem to point out the presence of additional thermomagnetic buoyancy forces to support the improvement of the cooling.

The objective of this work is to study the effect that the addition of magnetic nanoparticles to a natural ester has on its properties and its cooling capacity. Some samples of ferrofluid (natural ester with maghemite) have been prepared using different concentrations. These have been characterized by measuring their thermo-hydraulic and dielectric properties, to find an optimal concentration. Then, the cooling capacities of the optimal nanofluid and the base fluid have been tested in a transformer immersed in these liquids. The experimental platform allowed the measurement of temperatures in different locations at different load levels. Parallel simulations of these tests have been carried out with a Computational Fluid Dynamics model of the experimental platform. The results show an improvement of the insulating capacity of the base fluid with the addition of maghemite nanoparticles, and an enhanced cooling capacity.

The very high-power transformer lifespan depends mainly on the temperature that cellulose insulation reaches during its operation. Traditionally, its cooling has been carried out using mineral oil as coolant. Nowadays, alternative ester-based liquids are under study as substitutes due to their better environmental and fire-safety properties. This paper compares the cooling capacity of two ester-based fluids with that of a mineral oil using a 3D numerical model of a 100 MVA low voltage winding of a power transformer with axial cooling system and ONAN cooling mode. Heat-run test results with mineral oil have been used to validate this model. As a first approximation, according to the comparison developed, ester-based fluids could replace mineral oils in this type of transformers when they are going to work in a range of powers close to the rated one.

Amidst the new techniques facing the improvement of cooling and insulating efficiency and the design of electric transformers, constrained by the current technologies, one of the more promising is the substitution of traditional dielectric oils for nanofluids. Research on nanofluids for their application in transformers as a coolant and dielectric medium have been performed during the last two decades and continue today. This review tries to collect and analyze the available information in this field and to offer it already dissected to researchers, focusing on the preparation methods and how nanoparticles affect the main properties of the base fluids. Here we also addressed the influence of different parameters as particle characteristics or environmental conditions in nanofluids performance, the evolution with time of the measured properties, or the neighboring relationship of nanofluids with other transformer components. In this sense, the most reviewed articles reflect enhancements of thermal conductivity or dielectric strength, as well as an improvement of time evolution of these properties, with respect to those that are found in base fluids, and, also, a better interaction between these nanofluids and dielectric cellulosics. Thus, the use of dielectric nanofluids in transformers may allow these machines to work safer or over their design parameters, reducing the risk of failure of the electrical networks and enhancing their life expectancy. Nevertheless, these advantages will not be useful unless a proper stability of nanofluids is ensured, which is achieved in a small part of revised articles. A compendium of the preparation methodology with this aim is proposed, to be checked in future works.

The lifespan of an electrical transformer, primarily determined by the condition of its solid insulation, is well known under various operating conditions when mineral oil is the coolant in these machines. However, there is a trend toward replacing this oil with biodegradable fluids, especially esters; therefore, an understanding of the ageing of solid insulation with these fluids is essential. Currently available data do not allow for the selection of the best ester among those available on the market, as each study applies different conditions, making it impossible to compare results. Thus, this paper analyses the degradation of Kraft and Thermally Upgraded Kraft papers with the following five most promising commercial esters: sunflower, rapeseed, soybean, palm, and synthetic. The materials underwent accelerated thermal ageing at 130, 150, and 170 °C, and the integrity of the papers was evaluated through their polymerisation degree and the obtaining of the degradation kinetic models. The wide range of materials studied in this work, which were subjected to the same treatments, allows for a comparison of the esters, revealing significant differences in the impact of the alternative fluids. Sunflower, rapeseed, and soybean esters provided the best paper protection, i.e., the degree of polymerisation of Kraft paper in the tests at 150 °C decreased by 71% with these fluids, compared to the 83% reduction with mineral oil, 79% reduction with palm ester, and 75% reduction with synthetic ester. Furthermore, different kinetic models were obtained to predict the degradation; it was concluded that the Emsley model provides the best fit. Additionally, it was found that the behaviour of a dielectric fluid with one type of paper cannot be extrapolated, which is only noticeable in broad-scope studies.

Mineral oil has been used for many years in various electrical equipment, including transformers, as a cooling and insulation medium. However, its low biodegradability and poor performance in terms of fire protection have prompted the search for fluids to replace it, with vegetable oils being prominently considered. In this study, the dielectric, chemical, and physical properties of four vegetable oils obtained from different seeds (sunflower, rapeseed, soybean, and palm) and a biodegradable synthetic fluid are analysed throughout their lifespan in transformers. Their performances are compared with a traditional mineral oil to assess which one is more suitable for use in transformers employing this type of paper. To achieve this, the fluids were subjected to thermal ageing in combination with copper and a thermally upgraded kraft (TUK) paper, with its degradation controlled by measuring the degree of polymerisation. The results demonstrate that the origin of the vegetable oils affects their properties and degradation rates. It was found that most of the alternative fluids are suitable for use in transformers with the TUK paper and that they can increase their lifespan.