Over the last few decades the insulating performance of transformer oils has been broadly studied under the point of view of nanotechnology, which tries to improve the insulating and heat dissipation performance of transformer oils by suspending nanoparticles. Many authors have analyzed the thermal and dielectric behavior of vegetable oil based-nanofluids, however, very few works have studied the evolution of these liquids during thermal aging and their stability. In this paper has been evaluated the performance of aged vegetable oil based-nanofluids, which have been subjected to accelerated thermal aging at 150 °C. Nanoparticles of TiO₂ and ZnO have been dispersed in a commercial natural ester. Breakdown voltage, resistivity, dissipation factor and acidity of nanofluid samples have been measured according to standard methods, as well as stability. Moreover, it has been analyzed the degradation of Kraft paper through the degree of polymerization (DP). The results have showed that although nanoparticles improve breakdown voltage, they increase the ageing of insulation liquids and dielectric paper.

This contribution presents the early results of a R&D collaboration established between the University of Cantabria and the Power Transformer Manufacturer EFACEC. This paper tests two different techniques of steady state thermal modelling applied to power transformer windings, Computational Fluid Dynamics (CFD) and Thermal-Hydraulic Network Modelling (THNM). The state of the art of thermal modelling demonstrates that these techniques have been used to calculate both average and hotspot winding temperatures by solving the winding temperature and flows profiles within the winding. THNM models have worse accuracy than CFD in the predicted results. The improvement of these THNM models is a topic of study in transformer thermal modelling. The first goal of this paper is to test the accuracy of a new calibrated THNM model of a disc-type winding immersed in mineral oil. Then, this THNM model is tested with ester-based liquids, such as a natural ester and a synthetic ester, to determine if it can be applied to these liquids without further calibrations. Finally, the cooling performance of both type of liquids is compared using only the THNM model results. The results of this work show that the THNM model developed herein gives good estimations of temperatures compared to those obtained with CFD for both types of liquids. Also, the use of alternative fluids leads to lower temperatures when considering the same oil flow rate and temperature as inlet boundary condition.

The assessment of a TiO₂ vegetal-based dielectric nanofluid has been carried out, and its characteristics and behavior have been tested and compared with a previously tested maghemite nanofluid. The results obtained reflect a similar affectation of the main properties, with a maximal improvement of the breakdown voltage of 33% at 0.5 kg/m³, keeping the thermal conductivity and the viscosity almost constant, especially the first one. This thermal characterization agrees with the results obtained when applying the TiO₂ optimal nanofluid in the cooling of an experimental setup, with a slightly worse performance than the base fluid. Nevertheless, this performance is the opposite to that noticed with the ferrofluid, which was capable of improving the cooling of the transformer and decreasing its temperature. The similarities between the characterizations of both nanofluids, the differences in their cooling performances and their different magnetic natures seem to point out the presence of additional thermomagnetic buoyancy forces to support the improvement of the cooling.

The very high-power transformer lifespan depends mainly on the temperature that cellulose insulation reaches during its operation. Traditionally, its cooling has been carried out using mineral oil as coolant. Nowadays, alternative ester-based liquids are under study as substitutes due to their better environmental and fire-safety properties. This paper compares the cooling capacity of two ester-based fluids with that of a mineral oil using a 3D numerical model of a 100 MVA low voltage winding of a power transformer with axial cooling system and ONAN cooling mode. Heat-run test results with mineral oil have been used to validate this model. As a first approximation, according to the comparison developed, ester-based fluids could replace mineral oils in this type of transformers when they are going to work in a range of powers close to the rated one.

The objective of this work is to study the effect that the addition of magnetic nanoparticles to a natural ester has on its properties and its cooling capacity. Some samples of ferrofluid (natural ester with maghemite) have been prepared using different concentrations. These have been characterized by measuring their thermo-hydraulic and dielectric properties, to find an optimal concentration. Then, the cooling capacities of the optimal nanofluid and the base fluid have been tested in a transformer immersed in these liquids. The experimental platform allowed the measurement of temperatures in different locations at different load levels. Parallel simulations of these tests have been carried out with a Computational Fluid Dynamics model of the experimental platform. The results show an improvement of the insulating capacity of the base fluid with the addition of maghemite nanoparticles, and an enhanced cooling capacity.

Amidst the new techniques facing the improvement of cooling and insulating efficiency and the design of electric transformers, constrained by the current technologies, one of the more promising is the substitution of traditional dielectric oils for nanofluids. Research on nanofluids for their application in transformers as a coolant and dielectric medium have been performed during the last two decades and continue today. This review tries to collect and analyze the available information in this field and to offer it already dissected to researchers, focusing on the preparation methods and how nanoparticles affect the main properties of the base fluids. Here we also addressed the influence of different parameters as particle characteristics or environmental conditions in nanofluids performance, the evolution with time of the measured properties, or the neighboring relationship of nanofluids with other transformer components. In this sense, the most reviewed articles reflect enhancements of thermal conductivity or dielectric strength, as well as an improvement of time evolution of these properties, with respect to those that are found in base fluids, and, also, a better interaction between these nanofluids and dielectric cellulosics. Thus, the use of dielectric nanofluids in transformers may allow these machines to work safer or over their design parameters, reducing the risk of failure of the electrical networks and enhancing their life expectancy. Nevertheless, these advantages will not be useful unless a proper stability of nanofluids is ensured, which is achieved in a small part of revised articles. A compendium of the preparation methodology with this aim is proposed, to be checked in future works.