For years, drilling engineers have been faced with the challenge of drilling wells through naturally fractured reservoirs that are present around the world. During drilling, the pressure at the bottomhole of a well is frequently intentionally higher than formation pressure, which can result in the loss of mud in surrounding rocks. During well cementing, the bottomhole pressure is even higher than it is during drilling, because the cement slurry density is higher than the density of the mud. Therefore, if natural or induced fractures in the surrounding rocks are not plugged during drilling, the cement slurry can be lost to them, reducing their permeability which is undesirable in the case of a pay zone. To prevent the loss of circulation and the related consequences, it is necessary to apply good drilling and cementing practices and to use adequate methods and carefully selected materials for plugging the loss zones. The aim of this article is to give an overview of the preventive and corrective methods that can be applied in drilling and cementing through fractured zones as well as improvements in drilling and cementing technology to avoid lost circulation issues (e.g., aerated drilling fluid, casing while drilling, managed pressure drilling, expandable tubulars, lightweight cement slurries, etc.).

With the development of different segments within the drilling technology in the last three decades, well drilling has become possible in harsh downhole conditions. The vertical well provides access to oil and gas reserves located at a certain depth directly below the wellsite, and a large number of vertical wells are required for the exploitation of hydrocarbons from spatially expanded deposits. However, the borehole can deviate from the vertical well, which means that the target zone can be reached by a horizontal directional well. With this type of well, especially in the case of drilling an extended-reach well (ERW), the length of the wellbore in contact with the reservoir and/or several separate reservoirs is significantly increased, therefore, it is a much better option for the later production phase. Unfortunately, the application of extended-reach drilling (ERD technology), with all of its advantages, can cause different drilling problems mostly related to the increased torque, drag, hole cleaning and equivalent circulation density (ECD), as well as to an increase in the well price. Overcoming these problems requires continuous operational change to enable operators to address downhole challenges. Today, the longest well reaches 15,240 m (50,000 ft), which raises the question of the technological and economic feasibility of this type of drilling project, especially with the lower oil price on the energy market. This paper provides a comprehensive overview of extended-reach drilling technology, discusses the main problems and analyzes current achievements.

Oil and gas exploration and production activities generate large amounts of waste material, especially during well drilling and completion activities. Waste material from drilling activities to the greatest extent consists of drilled cuttings and used drilling mud with a smaller portion of other materials (wastewater, produced hydrocarbons during well testing, spent stimulation fluid, etc.). Nowadays, growing concerns for environmental protections and new strict regulations encourage companies to improve methods for the reduction of waste material, as well as improve existing and develop new waste disposal methods that are more environmentally friendly and safer from the aspect of human health. The main advantages of the waste injection method into suitable deep geological formations over other waste disposal methods (biodegradation, thermal treatment, etc.) are minimizing potentially harmful impacts on groundwater, reducing the required surface area for waste disposal, reducing the negative impact on the air and long-term risks for the entire environment. This paper gives a comprehensive overview of the underground waste injection technology, criteria for the selection of the injection zone and methods required for process monitoring, as well as a comprehensive literature overview of significant past or ongoing projects from all over the world.

The drilling of clay-rich formations, such as shale, is an extremely demanding technical and technological process. Shale consists of mixed clay minerals in different ratios and in contact with water from drilling mud. It tends to swell and cause different wellbore instability problems. Usually, the petroleum industry uses various types of salt and/or polymers as shale hydration inhibitors. The aim of this research was to determine whether nanoparticles can be used as shale swelling inhibitors because due to their small size they can enter the shale nanopores, plug them and stop further penetration of mud filtrate into the shale formation. Swelling of bentonite-calcium carbonate pellets after 2 and 24 h in water and drilling mud (water, bentonite, PAC and NaOH) without nanoparticles and with addition of TiO₂ (0.5, 1 and 1.5 wt%) and SiO₂ (0.5, 1 and 1.5 wt%) nanoparticles was measured using a linear swell meter. Additionally, granulometric analyses of bentonite as well as the zeta potential of tested muds containing nanoparticles were performed. Based on the laboratory research, it can generally be concluded that the addition of SiO₂ and TiO₂ nanoparticles in water and base drilling mud reduces the swelling of pellets up to 40.06%.

Wellbore instability is one of the most serious problems that can occur during drilling, mainly during drilling oil or gas wells through rocks that contain a higher proportion of clay, such as shales. To prevent wellbore instability, oil companies apply different approaches to strengthen wellbore walls, and use different shale swelling inhibitors. The aim of this research was to apply a green approach and the concept of the circular economy in mud design, and to determine whether mandarin peel powder, which is a waste material, can be used as an inhibitor of shale swelling. For that purpose, pellets consisting of bentonite and quartz in a 50:50 ratio were prepared using a compactor, and bentonite-based drilling mud (BM) with and without mandarin peel powder in concentrations of 0.5, 1, 1.5 and 2% by volume of water. The swelling of quartz–bentonite pellets after 2 and 24 h in each drilling-mud sample was determined at room temperature and 90 °C using a linear swell meter. On the basis of laboratory research, we concluded that increasing the concentration of mandarin peel powder reduces pellet swelling. By adding mandarin peel powder particles between 0.1 and 0.16 mm to the base mud at a concentration of 2% by volume of water, the following was achieved: 44% reduction in API filtration, 61.54% reduction in PPT filtration, 45% reduction in pellet swelling after 24 h at room temperature, and 48.6% reduction of pellet swelling after 24 h at 90 °C.

The term “small journal” has been used for a journal published as a single journal or one of a few serials, mostly by an academic publisher. This case study showed the challenges that a journal must override to be indexed in Scopus and WoS, especially if Q1/Q2 are targeted. The number of submissions, and especially of the published papers, are not the most critical variables for an increase of journal citations. The most important is the further activity of researchers included in the paper’s authorship, their future publication rate and continuation of similar research, which implies the citations of previous works belonging to the same authors and/or research groups. The larger the number of papers per issue, the increased probability of such an event, but there is no linear correlation. Moreover, the editorial work, especially during the initial editorial screening of received submissions, makes the consequent reviewer’s work easier, faster, and of higher quality, which certainly increases the quality of publications and their further citation life. The cited half-life vs. cited half-life ratio in small journals would need to be less than one (here 0.25), making the published papers fast cited, with first citations coming early enough that they could fit in a three-year window, and be countable for the calculation of indexing measures like Citescore or the Impact Factor.