This letter proposes a modified Y-source dc-dc converter, which features higher voltage-gains but lower voltage stresses on the components. Moreover, the proposed converter draws a continuous current from the dc input with much control flexibility (i.e., a wide range of adjustable duty cycles). Additionally, the coupled inductors have a low turns ratio, and the core saturation issue is avoided due to the dc-current-blocking capacitor. A detailed analysis of the proposed converter is provided, and the performance is benchmarked with selected coupled-inductors-based converters on various aspects. Experimental tests confirm the theoretical analysis.
16 May 2019 in IEEE Transactions on Power Electronics
This letter proposes a single switch magnetically coupled dc/dc converter with high voltage gain. The unique features of the converter are summarized as: 1) voltage gain of the converters is raised by lowering its magnetic turn ratio; 2) wide control range (0 < D < 1); 3) continuous current from the source that makes it a suitable candidate for renewable energy applications; 4) there is no dc current saturation in the core due to the presence of capacitor in the primary winding of the inductor. The feasibility of the proposed converter is studied in details supported by circuit analysis and simulation results. Further, the proposed converter is analyzed and compared with other converters with similar topologies. Finally the superior performance of the circuit is validated experimentally.
In this study, a modified DC–DC converter is proposed, which can achieve a high voltage‐gain exploiting both quasi‐Z‐source and switched‐capacitor networks. In addition to the high voltage‐gain, the proposed converter has low voltage stresses on its elements. The steady‐state analysis in both continuous and discontinuous conduction modes is given in this study. Moreover, the design of the passive elements, the calculation of the non‐ideal voltage gain, and the power loss analysis are done. Then, an extended topology of the proposed converter is presented, which further enhances the voltage gain, while maintaining the voltage stresses of the components. A comprehensive comparison with the prior‐art converters is performed to accentuate the advantages of the proposed converter. Finally, simulations and experimental tests are provided to substantiate the theoretical analysis.
7 September 2020 in IEEE Transactions on Power Electronics
This article presents the hardware, software, and power codesign of an ultra-efficient data storage server with differential power processing (DPP). DPP can reduce the power conversion stress, improve the efficiency, and enhance the functionality of modular power electronics systems. The power inputs of a large number of hard disk drives (HDDs) were connected in series and supported by a multiport ac-coupled differential power processing (MAC-DPP) converter through a multiwinding transformer. Methods for controlling the multi-input multi-output power flow in the multiwinding transformer while avoiding core saturation were investigated. A ten-port MAC-DPP prototype with 700-W/in $^3$ power density was built to support a 450-W HDD storage system with ten series-stacked voltage domains. The prototype was tested on a 50-HDD server testbench, and the overall system loss is below 1 W (99.77% system efficiency). The server was able to maintain high-speed reading and writing operation of all 50 HDDs against the worst hot-swapping scenarios. A variety of hardware/software configurations and many cloud storage techniques were tested on the fully functioning server. Experimental results show that the energy efficiency of large-scale information systems (CPU/GPU clusters, memory banks, HDD arrays, etc.) can be greatly improved by software, hardware, and power codesign.
Impedance source converters as single-stage power conversion alternatives can boost and regulate the output voltages of renewable energy sources. Nevertheless, they, also known as Z-source inverters (ZSIs), still suffer from limited voltage gains and higher stresses across the components. To tackle such issues, extra diodes, passive components, and active switches can be utilized in the basic ZSIs. In this paper, a modified switched-quasi-Z-source inverter (S-qZSI) is proposed, which features continuous input currents and high boosting capability to boost output voltage by minor modifications of a prior-art topology. Furthermore, the voltage stress of the active switches is reduced, which contributes to a lower cost. The operation principles are discussed comprehensively. The performance of the proposed ZSI in terms of conversion ratio, voltage gain, and stresses on the power switches and capacitors is benchmarked with selected ZSIs. Finally, simulations and experimental tests substantiate the theoretical analysis and superior performance.