Computer vision-based structural deformation monitoring techniques were studied in a large number of applications in the field of structural health monitoring (SHM). Numerous laboratory tests and short-term field applications contributed to the formation of the basic framework of computer vision deformation monitoring systems towards developing long-term stable monitoring in field environments. The major contribution of this paper was to analyze the influence mechanism of the measuring accuracy of computer vision deformation monitoring systems from two perspectives, the physical impact, and target tracking algorithm impact, and provide the existing solutions. Physical impact included the hardware impact and the environmental impact, while the target tracking algorithm impact included image preprocessing, measurement efficiency and accuracy. The applicability and limitations of computer vision monitoring algorithms were summarized.

As a reliable indicator of human physiological health, respiratory rate has been utilized in more and more cases for prediction and diagnosis of potential respiratory diseases and the respiratory dysfunction caused by cystic fibrosis. However, compared with smart mobile electronics, traditional clinical respiration monitoring systems is not convenient to work as a household wearable device for real-time respiration monitoring in daily life due to its cumbersome structure, complex operability, and reliance on external power sources. Thus, we propose a wearable wireless respiration sensor based on lateral sliding mode triboelectric nanogenerator (TENG) to monitor respiratory rates by sensing the variation of the abdominal circumference. In this paper, we validate the possibility of the device as a respiration monitoring sensor via an established theoretical model and investigate the output performance of the sensor via a series of mechanical tests. Furtherly, the applications of the respiration sensor in different individuals, different breathing rhythms, different active states, and wireless transmission have been verified by a lot of volunteer tests. All the results demonstrate the potential of the proposed wearable sensor as a new alternative for detecting and monitoring real-time respiratory rates with general applicability and sensitivity.

Structural health monitoring is of great significance to ensure the safety of marine pipes, while powering the required monitoring sensors remains a problem because the ocean environment is not amenable to the traditional ways of providing an external power supply. However, mechanical energy due to the vortex-induced vibration of pipelines may be harvested to power those sensors, which is a convenient, economic and environmentally friendly way. We here exploit a contact-separation mode triboelectric nanogenerator (TENG) to create an efficient energy harvester to transform the mechanical energy of vibrating pipes into electrical energy. The TENG device is composed of a tribo-pair of dielectric material films that is connected to a mass-spring base to guarantee the contact-separation motions of the tribo-pair. Experimental tests are conducted to demonstrate the output performance and long-term durability of the TENG device by attaching it to a sample pipe. A theoretical model for the energy harvesting system is developed for predicting the electrical output performance of the device. It is established that the normalized output power depends only on two compound variables with all typical factors taken into consideration simultaneously. The simple scale law is useful to reveal the underlying mechanism of the device and can guideline the optimization of the device based on multi-parameters analyses. The results here may provide references for designing contact-mode TENG energy harvesting devices based on the vibration of marine pipes and similar structures.

As a state-of-the-art method, the digital image correlation (DIC) technique is used to capture the fracture properties of wood along the longitudinal direction, such as the crack propagation, the strain field, and the fracture process zone (FPZ). Single-edge notched (SEN) specimens made of Douglas fir (Pseudotsuga menziesii) from Canada with different notch-to-depth ratios are tested by three-point-bending (3-p-b) experiment. The crack mouth opening displacements (CMOD) measured by the clip gauge and DIC technique agree well with each other, verifying the applicability of the DIC technique. Then, the quasi-brittle fracture process of wood is analyzed by combing the load-CMOD curve and the strain field in front of the preformed crack. Additionally, the equivalent elastic crack length is calculated using the linear superposition hypothesis. The comparison between the FPZ evolution and the equivalent elastic crack shows that specimens with higher notch-to-depth ratios have better cohesive effect and higher cracking resistance.

More and more researches have been carried out recently on Weigh-In-Motion (WIM) technology for solving the traffic safety problems caused by overload. In this article, we aim to study the measurement accuracy of the WIM system. Based on the electromechanical theory and elastic half-space method, we establish a theoretical model of multi-layer structure to investigate the correlation between the output voltage of the piezoelectric sensor and the applied force. In addition, we performed cyclic and moving load experiments to verify the accuracy of the analytical calculations. The load magnitude identified by this theoretical model matched the experiments very well, which shows that this model is effective for the WIM system. In addition, we proved that the load frequency is an important factor affecting the measurement accuracy of the sensor, which further enables us to design more suitable sensors for certain use scenarios.

Scavenging mechanical energy from the deformation of roadways using piezoelectric energy transformers has been intensively explored and exhibits a promising potential for engineering applications. We propose here a new packaging method that exploits MC nylon and epoxy resin as the main protective materials for the piezoelectric energy harvesting (PEH) device. Wheel tracking tests are performed, and an electromechanical model is developed to double evaluate the efficiency of the PEH device. Results indicate that reducing the embedded depth of the piezoelectric chips may enhance the output power of the PEH device. A simple scaling law is established to show that the normalized output power of the energy harvesting system relies on two combined parameters, i.e., the normalized electrical resistive load and normalized embedded depth. It suggests that the output power of the system may be maximized by properly selecting the geometrical, material, and circuit parameters in a combined manner. This strategy might also provide a useful guideline for optimization of piezoelectric energy harvesting system in practical roadway applications.