3D printing is a well-known technology for creating 3D objects by laying down successive layers of various materials. Among the wide range of applications, fashion industry has adapted these technologies to revolutionize their brands. But due to the unique characteristics of textiles like comfort, flexibility, and so on, attempts have been made to create similar structures as textiles. The work presented here is part of a project to create garments using fused deposition modeling as 3D printing technology. Structures with various geometries are designed and tested with different materials starting from rigid to flexible. As a result, a fully 3D printed dress is created. Selecting this dress as a model, consumer acceptance for 3D printed garments is evaluated realizing an online survey containing 100 respondents. The data gathered show that respondents have knowledge of 3D printing, its advantages and the majority of them would accept wearing a 3D printed dress.
7 December 2018 in IOP Conference Series: Materials Science and Engineering
Drape is one of the most important properties of fabric, which significantly influences the appearance of a garment or technical textile. Being closely related to stiffness and other mechanical parameters, drape is also influenced by seams and other modifications of the pure textile fabric. In most investigations, the drape coefficient according to Cusick is used to measure drape, using a special drape meter, which allows to quantitatively describing the textile's behaviour in terms of drape coefficient, number of nodes, etc. This article gives an overview of possibilities to modify fabric drape by printing different geometrical patterns on textile fabric. Their geometry and distance also influence on fabric drape. The resulting differences in a real garment using a skirt as an example will show the impact of 3D printing on garment drape.
Electrocardiogram (ECG) signals are often measured for medical purposes and in sports. While common Ag/AgCl glued gel electrodes enable good electrode skin contact, even during movements, they are not comfortable and can irritate the skin during long-term measurements. A possible alternative is textile electrodes, which have been investigated extensively during the last years. These electrodes, however, are usually not able to provide reliable, constant skin contact, resulting in reduced signal quality. Another important problem is the modification of the electrode surface due to washing or abrasion, which may impede the long-term use of such textile electrodes. Here, we report a study of washing and abrasion resistance of different ECG electrodes based on an isolating woven fabric with conductive embroidery and two conductive coatings, showing unexpectedly high abrasion resistance of the silver-coated yarn and optimum ECG signal quality for an additional coating with a conductive silicone rubber. Sheet resistances of the as-prepared electrodes were in the range of 20–30 Ω, which was increased to the range of 25–40 Ω after five washing cycles and up to approximately 50 Ω after Martindale abrasion tests. ECG measurements during different movements revealed reduced motion artifacts for the electrodes with conductive silicone rubber as compared to glued electrodes, suggesting that electronic filtering of such noise may even be easier for textile electrodes than for commercial electrodes.
1 January 2024 in Journal of Engineered Fibers and Fabrics
There is a growing trend where footwear is considered a fashion item by increasing in this way the number of footwear products in the market. This is translated to carbon footprints which is a global issue. Reducing the number of footwear can be achieved by focusing on customization. Shifting from mass production to customization is highly supported by digital technologies. A case study of shoe customization in the mass production mode is presented. Implemented in a shoe manufacturing environment, the possibility of using one node of the bottom in combination with various options for the shoe not only results in success in terms of fit and comfort but at the same time promotes sustainable production. This methodology aligns with the sustainability goals in the footwear industry while expanding the range of shoes.
Nanofiber mats can be electrospun by different techniques, usually subdivided into needle-based and needleless. The latter allow for producing large-area nanofiber mats, e.g., with a width of 50 cm and lengths of several meters, if electrospinning proceeds for several hours, depending on the required thickness. Even spinning smaller samples, however, raises the question of homogeneity, especially if defined mechanical properties or a defined thickness is required, e.g., for filtration purposes. Very often, only the inner parts of such electrospun nanofiber mats are used to avoid too high variation of the nanofiber mat thickness. For this study, we used wire-based electrospinning to prepare nanofiber mats with slightly varying spinning parameters. We report investigations of the thickness and mass per unit area, measured on different positions of needleless electrospun nanofiber mats. Martindale abrasion tests on different positions are added as a measure of the mechanical properties. All nanofiber mats show unexpectedly strong variations of thickness, mass per unit area, and porosity, as calculated from the apparent density of the membranes. The thickness especially varied by nearly one order of magnitude within one sample, while the apparent density, as the most uniform parameter, still showed variations by more than a factor of two within one sample. This shows that even for apparently highly homogeneous areas of such nanofiber mats, variations cannot be neglected for all potential applications.