The current study investigates the effects of Fiber Reinforce Polymer (FRP) additive on the performance of Stone Mastic Asphalt (SMA) mixtures with SBS and Viatop Premium additives. The asphalt mixture used in the current study included SBS (Styrene-Butadiene-Styrene) additive modified at the rate of 5% according to the necessary preliminary studies, and some SMA mixture modified by adding FRP (Fiber Reinforced Polymers) additive prepared in dimensions of 5 cm in different proportions (0.3%, 0.5%, 0.7% and 0.9%). The mechanical properties of the mixtures were investigated, and the findings revealed that the SMA mixture; prepared by adding FRP additive, SBS modified bitumen, and Viatop Premium additive; increased the rutting, aging resistance and elasticity of SMAs. Moreover, load spread ability and fatigue life revealed an increase, whereas high temperature sensitivity and tendency to crack at low temperatures decreased throughout the study. The FRP contribution rate that improves the performance characteristics of the SMA mixture to the highest level was found to be 0.7%.
1 November 2024 in Turkish Journal of Civil Engineering
Nowadays, the use of waste materials in various industries is becoming widespread in order to promote waste recycling. Thus, scientists are researching the use of waste materials in bitumen modification. In this study, it was aimed to investigate the effect of waste cooking oil (WCO) on the physical and rheological properties of unaged Styrene-Butadiene-Styrene modified bitumen (SBSMB) by adding WCO at different ratios (1, 3, 5, 7, and 9%) to SBS modified bitumen. Accordingly, rotational viscosity (RV) tests and rheological tests with dynamic shear rheometer (DSR) based on the determination of complex shear modulus (|G*|) and phase angle (δ) were conducted along with the traditional bitumen tests. As a result of the experimental study, it was observed that adding WCO increased the workability and fatigue resistance of SBSMB, however, decreased its rutting resistance. Therefore, the mixing and compaction temperatures of SBSMB can be decreased by adding low amounts of WCO without excessive performance loss. Thus, during the construction of asphalt pavements, environmental damage can be reduced by utilizing waste materials and reducing CO2 emissions.
1 July 2024 in Turkish Journal of Civil Engineering
With sustainability being the most crucial issue of recent years, the use of waste materials in bitumen modification is increasing and becoming widespread. In this experimental study, it was aimed to investigate the high- and low-temperature behavior of bitumen samples modified with waste cooking oil (WCO), reactive ethylene terpolymer (RET), and polyphosphoric acid (PPA). Accordingly, the multiple stress creep and recovery (MSCR) test and the bending beam rheometer (BBR) test were conducted. Depending on the increasing WCO ratio, the Jnr,R%,∆T_c,and λ parameters of modified bitumens were examined in detail. It was observed that with increasing WCO ratio,the Jnr value increased, and elastic recovery and stiffness decreased. In addition, it has been determined that this composite-modified bitumen is resistant to heavy traffic loads and has sufficient flexibility at low temperatures.
16 April 2024 in Arabian Journal for Science and Engineering
In recent years, various studies have shown that boron-containing additives improve the rutting performance of the bituminous pavements. However, in these studies, it was stated that these additives would decrease the workability of the bitumen and increase energy required for the construction of the pavement. On the other hand, it has been shown in many studies that waxes increase the workability of the bitumen. In this study, it was aimed to obtain bitumen with high rutting resistance and workability by adding boron oxide (BO) and beeswax (BW) to bitumen. Therefore, modified bitumen was produced by adding BO and BW at different ratios to a 50/70 penetration grade base bitumen. Then, the chemical, physical, and rheological properties of modified bitumen samples were investigated by various experiments. As a result, it has been observed that BO increases the high-temperature performance and viscosity of bitumen; on the other hand, BW decreases rutting resistance and viscosity. When BO and BW were added together to the bitumen, the negative impact of BO on workability and the negative impact of BW on high temperature performance were significantly eliminated. Especially, in 1BO + 1BW and 3BO + 3BW bitumens, the high-temperature performance of the bitumen improved without decreasing the workability.
1 April 2017 in Journal of the Croatian Association of Civil Engineers