The 14 November 2016 $Mw$ 7.8 Kaikōura earthquake generated more than 10,000 landslides over a total area of about $10,000km2$, with the majority concentrated in a smaller area of about $3600km2$. The largest landslide triggered by the earthquake had an approximate volume of $20(±2)Mm3$, with a runout distance of about 2.7 km, forming a dam on the Hapuku River. In this article, we present version 1.0 of the landslide inventory we have created for this event. We use the inventory presented in this article to identify and discuss some of the controls on the spatial distribution of landslides triggered by the Kaikōura earthquake. Our main findings are (1) the number of medium to large landslides (source area $≥10,000m2$) triggered by the Kaikōura earthquake is smaller than for similar‐sized landslides triggered by similar magnitude earthquakes in New Zealand; (2) seven of the largest eight landslides (from 5 to $20Mm3$) occurred on faults that ruptured to the surface during the earthquake; (3) the average landslide density within 200 m of a mapped surface fault rupture is three times that at a distance of 2500 m or more from a mapped surface fault rupture; (4) the “distance to fault” predictor variable, when used as a proxy for ground‐motion intensity, and when combined with slope angle, geology, and elevation variables, has more power in predicting landslide probability than the modeled peak ground acceleration or peak ground velocity; and (5) for the same slope angles, the coastal slopes have landslide point densities that are an order of magnitude greater than those in similar materials on the inland slopes, but their source areas are significantly smaller.

The collapse of a volcanic flank can be destructive and deadly. Hydrothermal alteration is common to volcanoes worldwide and is thought to promote volcano instability by decreasing rock strength. However, some laboratory studies have shown that not all alteration reduces rock strength. Our new laboratory data for altered rhyodacites from Chaos Crags (Lassen volcanic center, California, USA) show that pore- and crack-filling mineral precipitation can reduce porosity and permeability and increase strength, Young's modulus, and cohesion. A significant reduction in permeability, by as much as four orders of magnitude, will inhibit fluid circulation and create zones of high pore fluid pressure. We explored the consequences of pore fluid pressurization on volcano stability using large-scale numerical modeling. Upscaled physical and mechanical properties for hydrothermally altered rocks were used as input parameters in our modeling. Results show that a high-pore-pressure zone within a volcano increases volcano deformation and that increasing the size of this zone increases the observed deformation. Hydrothermal alteration associated with mineral precipitation, and increases to rock strength, can therefore promote pore pressurization and volcano deformation, increasing the likelihood of volcano spreading, flank collapses, and phreatic/phreatomagmatic explosions. We conclude that porosity-decreasing alteration, explored here, and porosity-increasing alteration can both promote volcano instability and collapse, but by different mechanisms. Hydrothermal alteration should therefore be monitored at volcanoes worldwide and incorporated into hazard assessments.

Volcanoes are unstable structures that deform laterally and frequently experience mass wasting events. Hydrothermal alteration is often invoked as a mechanism that contributes significantly to volcano instability. We present a study that combines laboratory experiments, geophysical data, and large‐scale numerical modeling to better understand the influence of alteration on volcano stability, using La Soufrière de Guadeloupe (Eastern Caribbean) as a case study. Laboratory experiments on variably altered (advanced argillic alteration) blocks show that uniaxial compressive strength, Young's modulus, and cohesion decrease as a function of increasing alteration, but that the internal friction angle does not change systematically. Simplified volcano cross sections were prepared (a homogenous volcano, a volcano containing the alteration zone identified by a recent electrical survey, and a volcano with an artificially enlarged area of alteration) and mechanical properties were assigned to zones corresponding to unaltered and altered rock. Numerical modeling performed on these cross sections, using a hydro‐thermo‐mechanical modeling code, show (a) the importance of using upscaled values in large‐scale models and (b) that alteration significantly increases volcano deformation and collapse volume. Finally, we combined published muon tomography data with our laboratory data to create a 3D strength map, exposing a low‐strength zone beneath the southern flank of the volcano coincident with the hydrothermal system. We conclude that hydrothermal alteration decreases volcano stability and thus expedites volcano spreading and increases the likelihood of mass wasting events and associated volcanic hazards. Hydrothermal alteration, and its evolution, should therefore be monitored at active volcanoes worldwide.