The application of Hall-based BLDC motors ranges from automotive accessory components such as oil and water pumps to high speed compressors. This paper proposes a new twelve-step unsymmetrical 160o commutation strategy using a single Hall-effect sensor method for brushless DC (BLDC) motor drives. The signal from the Hall-effect sensor is used to generate a number of pseudo Hall signals via a proposed speed-position estimator. The pseudo signals are then employed to control switching logic of a voltage source inverter (VSI). The effectiveness of the single Hall sensor method is examined on the unconventional 160o strategy, and on conventional 120o, 150o and 180o strategies with promising results. The paper presents a detailed comparison of the twelve-step unsymmetrical 160o commutation strategy with six-step voltage space vector that is used in conventional 120o and 180o strategies, and twelve-step symmetrical voltage space vector that is used in 150o strategy. Simulation results are validated via experimental measurements on a laboratory set-up using a real time dSPACE control environment, a representative BLDC motor prototype, a VSI and associated control components.
31 August 2017 in IEEE Transactions on Industrial Electronics
This paper presents the design of a high-voltage hybrid generator (HG) and conversion system for wind turbine applications. The HG combines wound field (WF) and permanent magnet (PM) rotor excitations. At any given speed, the PM induces a fixed stator voltage, while the WF induces a variable controlled stator voltage. The HG alternating output is rectified via a passive rectification stage; hence, the machine net dc output voltage is controlled over a prescribed, but a limited range. The split ratio between PM and WF rotor sections is considered as varying from a fully WF rotor, or traditional synchronous generator, to some ratio of PM to WF excitation. The turbine operational characteristics and maximum wind velocity variations between turbines in a wind farm are used to define the WF to PM split ratio. Both a three-phase and a nine-phase stator winding design are investigated. The nine-phase winding results in 4.2% higher output RMS voltage that yields a more power dense solution. It further yields lower rectified dc-link voltage ripple. The HG mass, loss audits, and efficiency discussions are presented. In order to investigate the feasibility of the HG concept, a small scale laboratory prototype is designed, and operational test results presented that show good agreement with the simulation model results.
17 April 2018 in IEEE Transactions on Energy Conversion
Design of a multiphase hybrid permanent magnet (HPM) generator for series hybrid electric vehicle (SHEV) application is presented in this paper. The proposed hybrid excitation topology together with an integral passive rectifier replaces the PM machine and active power electronics converter in hybrid/electric vehicles, facilitating the control over constant PM flux-linkage. The HPM topology includes two rotor elements, a PM and a wound field (WF) rotor, coupled on the same shaft in one machine housing. Both rotors share a 9-phase stator which results in higher output voltage and power density when compared to 3-phase design. The HPM generator design is based on a 3 kW benchmark PM machine to ensure the feasibility and validity of design tools and procedures. The WF rotor is designed to realize the same pole shape and number as in the PM section and to obtain the same flux-density in the air-gap while minimizing the WF input energy. A laboratory prototype HPM generator is built and tested and the measurements are compared with predicted results confirming the designed characteristics and machine performance. The paper also presents a comprehensive machine loss and mass audits.
22 October 2019 in IEEE Transactions on Industrial Electronics
This paper proposes a vector and a linear control strategy for wind turbines connecting to a DC collector grid. Two conversion schemes are considered for the wind turbine, (i) an active scheme where a dual rotor generator (DRG) is connected to a voltage source converter (VSC), and (ii) a passive scheme where a DRG is connected to a passive uncontrolled rectifier. The vector controller is implemented on VSC and DRG where the turbine rotor speed and output power are controlled via a VSC, and the wind turbine generator (WTG) rectified output DC voltage is controlled via a DRG DC filed current. A load-angle control and analytical modeling is discussed for the vector controller and evaluated via simulation results. In the passive scheme where the VSC is replaced with an uncontrolled rectifier the control is entirely shifted to DRG where a linear controller is implemented that controls the turbine rotor speed, power and voltage. A comparison of the vector and linear control is presented, and simulation results verify the effectiveness of the control strategy in steady-state and when turbine transitions between different wind velocities.
30 October 2019 in IEEE Transactions on Industrial Electronics