Akira Ishigami

Dr. Akira Ishigami

Graduate School of Organic Materials Science, Yamagata University
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 May 2020 in Materials
Verified
Journal Article
Open access
PDF file
TKTakashi Kurose
Takashi Kurose
AYAbe Yoshifumi
Abe Yoshifumi
MVMarcelo Vergne
Marcelo Vergne
YKYota Kanaya
Yota Kanaya
AIAkira Ishigami
Akira Ishigami
Hiroshi ItoHiroshi Ito
Hiroshi Ito
Metal specimens were fabricated via the fused deposition of metals (FDMet) technique with a filament composed of the 316L stainless steel particles and an organic binder. This process was adopted due to its potential as a low-cost additive manufacturing process. The objective of this study is to investigate the influence of the processing conditions—layer directions and layer thicknesses—on the mechanical and shrinkage properties of the metal components. The specimens were printed in three different layer directions. The highest ultimate strength of 453 MPa and strain at break of 48% were obtained in the specimen printed with the layer direction perpendicular to the tensile direction. On the other hand, the specimen printed in the layer direction parallel to the tensile direction exhibited poor mechanical properties. The reason for the anisotropy of the properties was investigated through systematic SEM observations. The observations revealed the presence of segregated binder domains in the filaments. It was deduced that the binder domain was oriented in the direction perpendicular to that of the layer and remained as oriented voids even after sintering. The voids oriented perpendicular to the tensile direction act as defects that could cause stress concentration, thus resulting in poor mechanical properties.

8 January 2021 in Angewandte Chemie International Edition
Verified
Journal Article
Closed access
PDF file
KSKota Seshimo
Kota Seshimo
HSHio Sakai
Hio Sakai
TWTakuma Watabe
Takuma Watabe
DADaisuke Aoki
Daisuke Aoki
HSHajime Sugita
Hajime Sugita
HOHideyuki Otsuka
Hideyuki Otsuka

3 July 2022 in Polymers
Verified
Journal Article
Open access
PDF file
Supaphorn ThumsornSupaphorn Thumsorn
Supaphorn Thumsorn
Wattanachai PrasongWattanachai Prasong
Wattanachai Prasong
TKTakashi Kurose
Takashi Kurose
AIAkira Ishigami
Akira Ishigami
YKYutaka Kobayashi
Yutaka Kobayashi
Hiroshi ItoHiroshi Ito
Hiroshi Ito
Commercial filaments of poly(lactic acid) (PLA) composites with particulate filler, carbon fiber, and copper powder with different contents were fabricated by FDM 3D printing in XZ-direction at bed temperatures of 45 °C and 60 °C. The effects of additives and bed temperatures on layer adhesion, fracture behavior, and mechanical performance of the PLA composites 3D printing were evaluated. Rheological properties informed viscous nature of all filaments and interface bonding in the PLA composites, which improved printability and dimensional stability of the 3D printing. Crystallinity of the PLA composites 3D printing increased with increasing bed temperature resulting in an improvement of storage modulus, tensile, and flexural properties. On the contrary, the ductility of the 3D printing was raised when printed at low bed temperature. Dynamic mechanical properties, the degree of entanglement, the adhesion factor, the effectiveness coefficient, the reinforcing efficiency factor, and the Cole–Cole analysis were used to understand the layer adhesion, and the interfacial interaction of the composites as compared to the compression molded sheets. SEM images revealed good adhesion between the additives and the PLA matrix. However, the additives induced faster solidification and showed larger voids in the 3D printing, which indicated lower layer adhesion as compared to neat PLA. It can be noted that the combination of the additives and the optimized 3D printing conditions would be obtain superior mechanical performance even layer adhesion has been restricted.

6 January 2021 in Materials
Verified
Journal Article
Open access
PDF file
AYAbe Yoshifumi
Abe Yoshifumi
TKTakashi Kurose
Takashi Kurose
MVMarcelo Vergne
Marcelo Vergne
YKYota Kanaya
Yota Kanaya
AIAkira Ishigami
Akira Ishigami
Hiroshi ItoHiroshi Ito
Hiroshi Ito
17-4PH stainless steel specimens were fabricated by fused deposition of metals (FDMet) technology, which combines 17-4PH particles with an organic binder. FDMet promises a low-cost additive manufacturing process. The present research aims to clarify the influence of layer directions in the 3D printing process on the mechanical and shrinkage properties of as-sintered and as-aged specimens. All specimens (the as-sintered and as-aged specimens printed in three layer directions) exhibited high relative density (97.5–98%). The highest ultimate strengths (880 and 1140 MPa in the as-sintered and as-aged specimens, respectively) were obtained when the layer direction was perpendicular to the tensile direction. Conversely, the specimens printed with their layer direction parallel to the tensile direction presented a low ultimate strength and low strain at breakage. The fact that the specimens with their layer direction parallel to the tensile direction presented a low ultimate strength and low strain at breakage is a usual behavior of parts obtained by means of FDM. The SEM images revealed oriented binder domains in the printed parts and oriented voids in the sintered parts. It was assumed that large binder domains in the filament were oriented perpendicular to the layer directions during the fused deposition modeling printing, and remained as oriented voids after sintering. Stress concentration in the oriented void defects was likely responsible for the poor tensile properties of these specimens.

28 March 2020 in Journal of Nanomaterials
Verified
Journal Article
Open access
PDF file
Wattanachai PrasongWattanachai Prasong
Wattanachai Prasong
PMParitat Muanchan
Paritat Muanchan
AIAkira Ishigami
Akira Ishigami
Supaphorn ThumsornSupaphorn Thumsorn
Supaphorn Thumsorn
TKTakashi Kurose
Takashi Kurose
Hiroshi ItoHiroshi Ito
Hiroshi Ito
Biodegradable poly(lactic acid) (PLA) filaments have been widely used in the fused deposition modeling (FDM) 3D printing technology. However, PLA has low toughness and low thermal resistance that affects printability and restricts its industrial applications. In this study, PLA was compounded with 0 to 40 wt% of poly(butylene adipate-co-terephthalate) (PBAT) and varied content of nano talc at 0 to 40 wt% in a twin screw extruder. The compounds were reextruded to filaments using a capillary rheometer. PLA/PBAT blends and their composite filaments were printed with a FDM 3D printing machine. Morphology, rheological behaviour, thermal characteristic, surface roughness, and mechanical property of 3D printing of the blends and the composites were investigated. Complex viscosity of the blends and the composites increased with increase of the PBAT and the nano talc contents. The incorporation of the nano talc enhanced crystallization temperature and reduced the coefficient of volume expansion of the composites. It was found that the PLA/PBAT blends and composites were excellent in both printability and dimension stability at PBAT content 10-30 wt% and nano talc up to 10 wt%. Interestingly, it was possible to print the composite filaments at an angle up to 75° during the overhang test without a supporter. From the vertical specimens, the surface roughness improved due to the incorporation of the nano talc. Tensile strength of the blends and the composites decreased, whereas elongation at break increased when the PBAT and the nano talc contents were increased. The reduction of tensile strength was attributed to agglomeration of the PBAT dispersed phase and less adhesion between the nano talc and the matrix. It can be noted that the composite 3D printing product showed superior elongation at break up to 410% by adding nano talc 1 wt%. This result suggests that the ductile 3D printable PLA/PBAT blend and the PLA/PBAT-nano talc composite products can be prepared, which shows potential for the commercialized scale.

27 February 2021 in Polymers
Verified
Journal Article
Open access
PDF file
Wattanachai PrasongWattanachai Prasong
Wattanachai Prasong
AIAkira Ishigami
Akira Ishigami
Supaphorn ThumsornSupaphorn Thumsorn
Supaphorn Thumsorn
TKTakashi Kurose
Takashi Kurose
Hiroshi ItoHiroshi Ito
Hiroshi Ito
Poly(lactic acid) (PLA) filaments have been the most used in fused deposition modeling (FDM) 3D printing. The filaments, based on PLA, are continuing to be developed to overcome brittleness, low heat resistance, and obtain superior mechanical performance in 3D printing. From our previous study, the binary blend composites from PLA and poly(butylene adipate-co-terephthalate) (PBAT) with nano talc (PLA/PBAT/nano talc) at 70/30/10 showed an improvement in toughness and printability in FDM 3D printing. Nevertheless, interlayer adhesion, anisotropic characteristics, and heat resistance have been promoted for further application in FDM 3D printing. In this study, binary and ternary blend composites from PLA/PBAT and poly(butylene succinate) (PBS) with nano talc were prepared at a ratio of PLA 70 wt. % and blending with PBAT or PBS at 30 wt. % and nano talc at 10 wt. %. The materials were compounded via a twin-screw extruder and applied to the filament using a capillary rheometer. PLA/PBAT/PBS/nano talc blend composites were printed using FDM 3D printing. Thermal analysis, viscosity, interlayer adhesion, mechanical properties, and dimensional accuracy of binary and ternary blend composite 3D prints were investigated. The incorporation of PBS-enhanced crystallinity of the blend composite 3D prints resulted in an improvement to mechanical properties, heat resistance, and anisotropic characteristics. Flexibility of the blend composites was obtained by presentation of PBAT. It should be noted that the core–shell morphology of the ternary blend influenced the reduction of volume shrinkage, which obtained good surface roughness and dimensional accuracy in the ternary blend composite 3D printing.