Hiroshi Ito

Prof. Hiroshi Ito

Yamagata University
orcid

Research Focus & Metrics

Academic Career Length

38Years (1989-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 May 2020 in Materials
Verified
Journal Article
Open access
PDF file
TKTakashi Kurose
Takashi Kurose
AYAbe Yoshifumi
Abe Yoshifumi
MVMarcelo Vergne
Marcelo Vergne
YKYota Kanaya
Yota Kanaya
AIAkira Ishigami
Akira Ishigami
Hiroshi ItoHiroshi Ito
Hiroshi Ito
Metal specimens were fabricated via the fused deposition of metals (FDMet) technique with a filament composed of the 316L stainless steel particles and an organic binder. This process was adopted due to its potential as a low-cost additive manufacturing process. The objective of this study is to investigate the influence of the processing conditions—layer directions and layer thicknesses—on the mechanical and shrinkage properties of the metal components. The specimens were printed in three different layer directions. The highest ultimate strength of 453 MPa and strain at break of 48% were obtained in the specimen printed with the layer direction perpendicular to the tensile direction. On the other hand, the specimen printed in the layer direction parallel to the tensile direction exhibited poor mechanical properties. The reason for the anisotropy of the properties was investigated through systematic SEM observations. The observations revealed the presence of segregated binder domains in the filaments. It was deduced that the binder domain was oriented in the direction perpendicular to that of the layer and remained as oriented voids even after sintering. The voids oriented perpendicular to the tensile direction act as defects that could cause stress concentration, thus resulting in poor mechanical properties.

8 January 2021 in Angewandte Chemie International Edition
Verified
Journal Article
Closed access
PDF file
KSKota Seshimo
Kota Seshimo
HSHio Sakai
Hio Sakai
TWTakuma Watabe
Takuma Watabe
DADaisuke Aoki
Daisuke Aoki
HSHajime Sugita
Hajime Sugita
HOHideyuki Otsuka
Hideyuki Otsuka


3 July 2022 in Polymers
Verified
Journal Article
Open access
PDF file
Supaphorn ThumsornSupaphorn Thumsorn
Supaphorn Thumsorn
Wattanachai PrasongWattanachai Prasong
Wattanachai Prasong
TKTakashi Kurose
Takashi Kurose
AIAkira Ishigami
Akira Ishigami
YKYutaka Kobayashi
Yutaka Kobayashi
Hiroshi ItoHiroshi Ito
Hiroshi Ito
Commercial filaments of poly(lactic acid) (PLA) composites with particulate filler, carbon fiber, and copper powder with different contents were fabricated by FDM 3D printing in XZ-direction at bed temperatures of 45 °C and 60 °C. The effects of additives and bed temperatures on layer adhesion, fracture behavior, and mechanical performance of the PLA composites 3D printing were evaluated. Rheological properties informed viscous nature of all filaments and interface bonding in the PLA composites, which improved printability and dimensional stability of the 3D printing. Crystallinity of the PLA composites 3D printing increased with increasing bed temperature resulting in an improvement of storage modulus, tensile, and flexural properties. On the contrary, the ductility of the 3D printing was raised when printed at low bed temperature. Dynamic mechanical properties, the degree of entanglement, the adhesion factor, the effectiveness coefficient, the reinforcing efficiency factor, and the Cole–Cole analysis were used to understand the layer adhesion, and the interfacial interaction of the composites as compared to the compression molded sheets. SEM images revealed good adhesion between the additives and the PLA matrix. However, the additives induced faster solidification and showed larger voids in the 3D printing, which indicated lower layer adhesion as compared to neat PLA. It can be noted that the combination of the additives and the optimized 3D printing conditions would be obtain superior mechanical performance even layer adhesion has been restricted.

8 January 2003 in Journal of Macromolecular Science, Part B
Verified
Journal Article
Closed access
MTMidori Takasaki
Midori Takasaki
Hiroshi ItoHiroshi Ito
Hiroshi Ito
TKTakeshi Kikutani
Takeshi Kikutani
High-speed melt spinning of racemate polylactide (r-PLA), which is a blend of equal amounts of poly(l-lactide) and poly(d-lactide) molecules, was performed up to the take-up velocity of 7.5 km/min. In the fiber structure analysis, particular attention was paid to the formation of stereocomplex crystals, because this crystal form has a melting temperature about 60° higher than the homocrystals. It was found that highly oriented and highly crystallized fibers containing the α-form and stereocomplex crystals were obtained when the take-up velocity exceeded about 4 km/min. The amount of stereocomplex crystal was higher under the spinning conditions of higher take-up velocity, lower throughput rate, and lower extrusion temperature. Under these conditions, higher tensile stress can be applied to the spinning line, and therefore, the orientation-induced crystallization is promoted. Annealing of the fibers obtained at high-take-up velocities, such as 6 km/min, which already have the crystalline structure with a c...

6 January 2021 in Materials
Verified
Journal Article
Open access
PDF file
AYAbe Yoshifumi
Abe Yoshifumi
TKTakashi Kurose
Takashi Kurose
MVMarcelo Vergne
Marcelo Vergne
YKYota Kanaya
Yota Kanaya
AIAkira Ishigami
Akira Ishigami
Hiroshi ItoHiroshi Ito
Hiroshi Ito
17-4PH stainless steel specimens were fabricated by fused deposition of metals (FDMet) technology, which combines 17-4PH particles with an organic binder. FDMet promises a low-cost additive manufacturing process. The present research aims to clarify the influence of layer directions in the 3D printing process on the mechanical and shrinkage properties of as-sintered and as-aged specimens. All specimens (the as-sintered and as-aged specimens printed in three layer directions) exhibited high relative density (97.5–98%). The highest ultimate strengths (880 and 1140 MPa in the as-sintered and as-aged specimens, respectively) were obtained when the layer direction was perpendicular to the tensile direction. Conversely, the specimens printed with their layer direction parallel to the tensile direction presented a low ultimate strength and low strain at breakage. The fact that the specimens with their layer direction parallel to the tensile direction presented a low ultimate strength and low strain at breakage is a usual behavior of parts obtained by means of FDM. The SEM images revealed oriented binder domains in the printed parts and oriented voids in the sintered parts. It was assumed that large binder domains in the filament were oriented perpendicular to the layer directions during the fused deposition modeling printing, and remained as oriented voids after sintering. Stress concentration in the oriented void defects was likely responsible for the poor tensile properties of these specimens.