Cindy Goppold

Dr. Cindy Goppold

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2014 in Physics Procedia
Verified
Journal Article
Open access
CGCindy Goppold
Cindy Goppold
KZKarsten Zenger
Karsten Zenger
PHPatrick Herwig
Patrick Herwig
AWAndreas Wetzig
Andreas Wetzig
Achim MahrleAchim Mahrle
Achim Mahrle
EBEckhard Beyer
Eckhard Beyer
A systematic experimental investigation of fiber laser cutting stainless steel in a wide range of material thicknesses is performed. The achievable maximum cutting speed, the resultant thermal efficiency of the process as well as the surface roughness of the cut edges were determined using different optical setups and beam geometries. In order to find out some reasons for characteristic features of the fiber laser cutting process also the cut kerf geometries were analyzed. The systematic investigation clarifies the most promising procedural possibilities for improvements of cutting performance and cut edge quality in fiber laser cutting of stainless steel

1 February 2016 in Advanced Optical Technologies
Verified
Journal Article
Closed access
CGCindy Goppold
Cindy Goppold
TPThomas Pinder
Thomas Pinder
PHPatrick Herwig
Patrick Herwig
Sheet metals with thicknesses >8 mm have a distinct cutting performance. The free choice of the optical configuration composed of fiber diameter, collimation, and focal length offers many opportunities to influence the static beam geometry. Previous analysis points out the limitations of this method in the thick section area. Within the present study, an experimental investigation of fiber laser fusion cutting of 12 mm stainless steel was performed by means of dynamical beam oscillation. Two standard optical setups are combined with a highly dynamic galvano-driven scanner that achieves frequencies up to 4 kHz. Dependencies of the scanner parameter, the optical circumstances, and the conventional cutting parameters are discussed. The aim is to characterize the capabilities and challenges of the dynamic beam shaping in comparison to the state-of-the-art static beam shaping. Thus, the trials are evaluated by quality criteria of the cut edge as surface roughness and burr height, the feed rate, and the cut kerf geometry. The investigation emphasizes promising procedural possibilities for improvements of the cutting performance in the case of fiber laser fusion cutting of thick stainless steel by means of the application of a highly dynamic scanner.

27 April 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
CGCindy Goppold
Cindy Goppold
TPThomas Pinder
Thomas Pinder
SSSusanne Schulze
Susanne Schulze
PHPatrick Herwig
Patrick Herwig
Andrés Fabián LasagniAndrés Fabián Lasagni
Andrés Fabián Lasagni
The latest research on laser beam fusion cutting (LBFC) with static beam shaping have shown a limitation in the quality of cut parts for thick steel plates (> 6 mm) when using solid state lasers. The approach of dynamic beam oscillation has recently shown to be capable of overcoming this challenge, allowing to increase the cutting speed as well as improving cut edge quality beyond the state of the art. The present paper investigates the influence of longitudinal, linear beam oscillation in LBFC of 12 mm mild and stainless steel plates by analyzing different parameters as cutting speed, burr, surface roughness, heat affected zone (HAZ), and recast layer. Reasons for the observed process improvements compared to static beam shaping have been discussed. The adjustment of the energy deposition and interaction time of the laser beam with the material found to be most relevant for optimizing the LBFC process. In particular, for beam oscillation, a gradual energy deposition takes place and increases the interaction time. This reduces the heat input in terms of HAZ and recast layer by more than 50%, resulting in high cut edge quality and more than 70% faster cutting speed.

20 January 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
TPThomas Pinder
Thomas Pinder
CGCindy Goppold
Cindy Goppold
The latest research on applying beam oscillation in laser beam fusion cutting revealed significant process improvements regarding speed and quality. The reason for this increasing process efficiency remains unexplained; however, theoretical investigations suggest the change in energy deposition (respectively heat conduction) as the cause. The present paper aims to analyze the energy deposition by a novel temperature measurement method. For this purpose, a conventional laser beam cutting setup was equipped with beam oscillation technology and a high-speed temperature measurement setup. Various characteristics of the temperature distribution in the process zone (spatial and temporal resolved temperature profiles, maximum and average values, as well as melt pool size) were evaluated for different conditions of beam oscillation (amplitude, frequency, cutting speed). Additionally, the geometrical properties of the process zone, defining the absorptivity have been measured. The comparison with static beam shaping reveals strong temperature volatility, which is induced by the way of energy deposition and an improved absorptivity over a substantial part of the cut front, with the overall result of enhanced heat conduction. For the first time, changed mechanisms applying beam oscillation instead of static beam shaping have been experimentally identified. Based on these measurements, a previously developed explanatory model was not only confirmed but also extended.

26 April 2016 in Journal of Laser Applications
Verified
Journal Article
Closed access
CGCindy Goppold
Cindy Goppold
TPThomas Pinder
Thomas Pinder
PHPatrick Herwig
Patrick Herwig
An increase of the cut quality or enhanced process efficiency is still an aim for cutting of thick metal plates with 1.07 μm laser radiation. Nowadays, linear polarization is well investigated for CO2-lasers as an approach to a solution. The same attempt is not explored as much for laser beam fusion cutting of thick metal plates with high power solid state lasers. For this case, the present letter examines the linear polarization in contrast to statistically polarized cuts.