The research in this study focused on the operating parameters for a high efficiency hydrogen production rate system, with the aim to design a hydrolysis of the NaBH4 hydrogen production module for lightweight and efficient hydrogen production and conversion. The experiment used a reactor, where the reaction volume was about 12 mL. The parameters on the feed rate of the NaBH4 solution and the catalyst loading for the hydrogen production rate and conversion efficiency were investigated. The catalyst is sufficient to allow the release of hydrogen in the 1 g/min solution, but the efficiency of hydrogen production at high flow rates has been shown to be low in previous studies. Therefore, the aim is to increase the catalyst to improve the reaction efficiency in this study. The results show that at the high temperature reaction condition, solid NaBO2 will not generate on the catalyst surface to influence the hydrogen production rate when using the five pcs catalyst. When the reaction temperature was 108 °C, the average hydrogen production rate was 1.72 L/min, and the conversion efficiency was 91.2%.
30 April 2021 in Mathematical Problems in Engineering
A joint theoretical and numerical study was carried out to investigate the fluid dynamical aspect of the motion of a vortex generated in a rotating tank with a sloping bottom. This study aims at understanding the evolution of strong cyclonic motions on a β-plane in the Northern Hemisphere. The strong cyclonic vortices were characterized by four nondimensional parameters which were derived through a scale analysis of the depth variations of fluid. By simplifying the model flow field and the prototype flow field, respectively, through the conservation of potential vorticity, two sets of dynamic similarity conditions are derived. This study proposed a sophisticated modified shallow water model (MSWM) to investigate the flow features of such strong vortices. A detailed numerical calculation adopted by multidimensional positive definite advection transport algorithm (MPDATA) was carried out to validate those effects considered in the MSWM model, including sloping bottom, parabolic free surface deformation, and viscous dissipation. Close agreements were found between the experimental and numerical results, including the streamlines patterns and the vortex trajectory. Comprehensive simulations for strong cyclonic vortices over different sloping bottoms were investigated to understand the impact of planetary β effect on vortex. The results calculated by MSWM demonstrate a variety of flow features of interactions between the primary vortex and induced secondary Rossby wave wakes that were essential and prominent in environmental geophysical flows.
The reversible solid oxide cell model is established by COMSOL Multiphysics® (version 5.4) software under multi-physics coupling. According to the governing equation, the simulations were conducted based on the same parameters for many control groups numerically. At the same time, a comparison of these results was involved. For the air electrode in SOFC mode, the performance of the fuel cell will increase with the increase in the porosity. For the fuel electrode in SOFC mode, the increase is much greater than the impact of the porosity. The design parameters compared in this simulation are used to simulate and analyze and predict fuel cell performance under different conditions. The design parameters related to the electrode microstructure are defined in this model as: porosity (electrode porosity), pore size (electrode internal average pore size), and permeability (electrode internal permeability).
Based on the active promotion plan (“New & Clean Energy Research & Development proposal in Taiwan” published by Bureau of Energy, Ministry of Economic Affairs, R.O.C.), the related topics were studied by balanced scorecard analysis, questionnaire investigation method, Delphi method and Analytic Hierarchy Process (AHP) in this paper. The result of the questionnaire indicated that the key-points of the renewable energy development in Taiwan are to set up the solid factory to establish the local technology using the government encouragement plan in the present stage. Then, it needs to expand the independent market and promote the application degree in the second stage. To simplify the process of the application and to get the oversea market through the technical output are the future goals in the following stage. For Delphi method, the expert interview results showed that the present related guidelines & encouragement plan are not complete for the application of renewable energy in Taiwan. The main problem is that the resources in all circles still need to be coordinated to focus the efforts for promotion. By impelling the related industries to form an alliance, learning from the development experience of the correlation industries, establishing the local technology and emphasizing the promotion of the society applications, the renewable energy industry in Taiwan can be expanded to potential scale. For the investigation of execution performance evaluation model, the Analytic Hierarchy Process (AHP) was applied to evaluate the weighting factor of the key-point of the questionnaire and expert interview results. All the promotion guidelines, encouragement plan and application process for investor should be fitted to the overseas standard as possible as it can. For achieving the global average standard, the technique transfer by importation (at least three items) and R&D of local technology (37 patents per year) should be carried on synchronously during the promotion periods. Finally, the software of this performance measure was constructed for the reference.
1 November 2010 in Journal of Information and Optimization Sciences
The purpose of this study is to design a LHV (Low Heating Value) fuel combustor and apply it in a 10KW gas turbine engine for power generation. The source of LHV fuel is produced from gasifi cation in oxygen-defi cient combustion of waste plastic; its heating value is about 6.7 MJ/m3. Composition, adiabatic fl ame temperature, flammable range, burning rate of this fuel are analyzed in this paper. In combustor design, turbine air jet flow initiated recirculation flow structure is adopted to strengthen mixing and flame holding eff ect. The fuel is supplied through axial vortex to enhance local mixing of fuel and air. The current design is evaluatedaccording to previous experience and one-dimensional flow-fi eld characteristic. The detailed flow structure was obtained from numeric simulation analysis of 3D isothermal flow-fi eld. The preliminary conclusion is that better air / fuel mixing effect can be achieved by adopting configuration of co-swirlers recirculation flow.