Ay Su

Prof. Dr. Ay Su


Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 February 2005 in International Journal of Energy Research
Verified
Journal Article
Closed access
PDF file
ASAy Su
Ay Su
YCY. C. Chiu
Y. C. Chiu
FWF. B. Weng
F. B. Weng
In this study, we present a rigorous mathematical model, to treat prediction and analysis of proton exchange membrane fuel cells gas concentration and current density distribution in mass transfer area and chemical reaction area performed in 3-D geometry. The model is based on the solution of the conservation equations of mass, momentum, species, and electric current in a fully integrated finite-volume solver using the CFDRC commercial code. The influences of fuel cell performance with two kinds of flow channel pattern design are studied. The gas concentration of the straight flow pattern appears excessively non-uniform, resulting in a local concentration polarization. On the other hand, the gas concentration is well distributed for the serpentine flow pattern, creating a better mass transfer phenomena. The performance curves (polarization curves) are also well correlated with experimental data. Copyright © 2005 John Wiley & Sons, Ltd.

20 June 2012 in International Journal of Energy Research
Verified
Journal Article
Closed access
PDF file
ZHZhen-Ming Huang
Zhen-Ming Huang
ASAy Su
Ay Su
YLYing-Chieh Liu
Ying-Chieh Liu
High-purity hydrogen generated by the hydrolysis of sodium borohydride can be used as proton exchange membrane fuel cells (PEMFCs) for portable device applications. Because of its advantages in high storage capacity, controllable reaction, and mild condition, hydrogen generation by catalytic hydrolysis of a chemical hydride, such as sodium borohydride, has recently attracted much attention for development. Hydrogen generated by the hydrolysis of sodium borohydride using a Ru catalyst is reported in the present study. A multi-layer coating process was used on the Ru/Ni foam catalyst to enhance the cycling generation. The optimal deposition density of the Ru particle on Ni foam was confirmed by SEM morphology. The cycling generation for the steady state reaction can be maintained at least 10 times, and gradually decreases to 82% performance after the 17th cycling generation. It was found that a combination of 20 wt% NaBH4 solution concentration and 3 wt% NaOH yields the highest performance for hydrogen generation. A hydrogen generation efficiency of 95% was obtained for a solution with a 1-g/min flow rate flowing onto the 6-cm2 area of a catalyst plate, which had a hydrogen generation rate of 0.45 L/min. As the solution flow rate was increased, the reaction efficiency decreased because of the decreased reaction time. Hydrogen fuel saturated with water generated by a NaBH4 solution shows an advantage over that from a gas cylinder for fuel cell operation. A PEM fuel cell was integrated with the hydrogen generator in the present study. The hydrogen fuel from the hydrogen generator with saturated water vapor showed a better cell performance compared with using hydrogen from a gas cylinder. Copyright © 2012 John Wiley & Sons, Ltd.

26 June 2009 in Sensors
Verified
Journal Article
Open access
PDF file
Chi-Yuan LeeChi-Yuan Lee
Chi-Yuan Lee
ASAy Su
Ay Su
YLYin-Chieh Liu
Yin-Chieh Liu
WFWei-Yuan Fan
Wei-Yuan Fan
WHWei-Jung Hsieh
Wei-Jung Hsieh
This investigation aimed to fabricate a flexible micro resistive temperature sensor to measure the junction temperature of a light emitting diode (LED). The junction temperature is typically measured using a thermal resistance measurement approach. This approach is limited in that no standard regulates the timing of data capture. This work presents a micro temperature sensor that can measure temperature stably and continuously, and has the advantages of being lightweight and able to monitor junction temperatures in real time. Micro-electro-mechanical-systems (MEMS) technologies are employed to minimize the size of a temperature sensor that is constructed on a stainless steel foil substrate (SS-304 with 30 μm thickness). A flexible micro resistive temperature sensor can be fixed between the LED chip and the frame. The junction temperature of the LED can be measured from the linear relationship between the temperature and the resistance. The sensitivity of the micro temperature sensor is 0.059 ± 0.004 Ω/°C. The temperature of the commercial CREE® EZ1000 chip is 119.97 °C when it is thermally stable, as measured using the micro temperature sensor; however, it was 126.9 °C, when measured by thermal resistance measurement. The micro temperature sensor can be used to replace thermal resistance measurement and performs reliably.

22 April 2020 in Catalysts
Verified
Journal Article
Open access
PDF file
JLJai-Houng Leu
Jai-Houng Leu
ASAy Su
Ay Su
SJSun Jungkang
Sun Jungkang
ZHZhen-Ming Huang
Zhen-Ming Huang
The research in this study focused on the operating parameters for a high efficiency hydrogen production rate system, with the aim to design a hydrolysis of the NaBH4 hydrogen production module for lightweight and efficient hydrogen production and conversion. The experiment used a reactor, where the reaction volume was about 12 mL. The parameters on the feed rate of the NaBH4 solution and the catalyst loading for the hydrogen production rate and conversion efficiency were investigated. The catalyst is sufficient to allow the release of hydrogen in the 1 g/min solution, but the efficiency of hydrogen production at high flow rates has been shown to be low in previous studies. Therefore, the aim is to increase the catalyst to improve the reaction efficiency in this study. The results show that at the high temperature reaction condition, solid NaBO2 will not generate on the catalyst surface to influence the hydrogen production rate when using the five pcs catalyst. When the reaction temperature was 108 °C, the average hydrogen production rate was 1.72 L/min, and the conversion efficiency was 91.2%.

7 April 2010 in Sensors
Verified
Journal Article
Open access
PDF file
Chi-Yuan LeeChi-Yuan Lee
Chi-Yuan Lee
ASAy Su
Ay Su
YLYin-Chieh Liu
Yin-Chieh Liu
PCPin-Cheng Chan
Pin-Cheng Chan
CLChia-Hung Lin
Chia-Hung Lin
In this work micro temperature and humidity sensors are fabricated to measure the junction temperature and humidity of light emitting diodes (LED). The junction temperature is frequently measured using thermal resistance measurement technology. The weakness of this method is that the timing of data capture is not regulated by any standard. This investigation develops a device that can stably and continually measure temperature and humidity. The device is light-weight and can monitor junction temperature and humidity in real time. Using micro-electro-mechanical systems (MEMS), this study minimizes the size of the micro temperature and humidity sensors, which are constructed on a stainless steel foil substrate (40 μm-thick SS-304). The micro temperature and humidity sensors can be fixed between the LED chip and frame. The sensitivities of the micro temperature and humidity sensors are 0.06 ± 0.005 (Ω/°C) and 0.033 pF/%RH, respectively.

23 June 2014 in Energies
Verified
Journal Article
Open access
GJGuo-Bin Jung
Guo-Bin Jung
LFLi-Hsing Fang
Li-Hsing Fang
MCMin-Jay Chiou
Min-Jay Chiou
XNXuan-Vien Nguyen
Xuan-Vien Nguyen
ASAy Su
Ay Su
JYJyun-Wei Yu
Jyun-Wei Yu
Commercially available tapes (anode, electrolyte) and paste (cathode) were choosen to prepare anode-supported cells for solid oxide fuel cell applications. For both anode-supported cells or electrolyte-supported cells, the anode needs pretreatment to reduce NiO/YSZ to Ni/YSZ to increase its conductivity as well as its catalytic characteristics. In this study, the effects of different pretreatments (open-circuit, closed-circuit) on cathode and anodes as well as SOFC performance are investigated. To investigate the influence of closed-circuit pretreatment on the NiO/YSZ anode alone, a Pt cathode is utilized as reference for comparison with the LSM cathode. The characterization of the electrical resistance, AC impedance, and SOFC performance of the resulting electrodes and/or anode-supported cell were carried out. It’s found that the influence of open-circuit pretreatment on the LSM cathode is limited. However, the influence of closed-circuit pretreatment on both the LSM cathode and NiO/YSZ anode and the resulting SOFC performance is profound. The effect of closed-circuit pretreatment on the NiO/YSZ anode is attributed to its change of electronic/pore structure as well as catalytic characteristics. With closed-circuit pretreatment, the SOFC performance improved greatly from the change of LSM cathode (and Pt reference) compared to the Ni/YSZ anode.