This manuscript reports the first leaky-wave antenna (LWA) array excited by a photomixer as well as its potential application for alignment in wireless links. The designed array is manufactured in printed circuit board (PCB) technology, works at the E-band (from 75 to 85 GHz), and provides a directive beam of about 18 dBi with a frequency scanning span of 22°. The antenna element consists of a microstrip line periodically loaded with stubs, and it has been designed employing a hybrid approach combining full-wave simulations and transmission line theory. This approach enables the optimization of the periods when the open-stopband of the LWA is mitigated or removed at the frequency of broadside emission. The proposed antenna was first tested using a ground signal ground (GSG) probe; the measured return loss and radiation patterns of the fabricated prototype were in good agreement with full-wave simulations. Then, the LWA array was integrated with the photomixer chip using conductive epoxy threads. Measurements of the radiated power yielded a maximum of 120 µW at 80.5 GHz for a 9.8 mA photocurrent. Finally, the antenna was used in a 25 cm wireless link, obtaining a 2.15 Gbps error-free data rate.
8 January 2025 in IEEE Transactions on Antennas and Propagation
The self-healing property of Bessel beams (BBs) is used to create a robust wireless link at W-band, maintaining high data rates despite metallic obstructions within their nondiffractive range (NDR). This is demonstrated experimentally using a broadband launcher, which comprises a photonic transmitter and a spline-profile horn, by placing a circular metallic obstacle in the beam’s path. Field measurements show the BB profile remains intact after the obstacle over the 75–105 GHz band. Power transmission tests reveal a record broadband efficiency of up to 70% (-1.54 dB) at 99 GHz across distances of 10 to 30 wavelengths. Bit error rate and real-time communication tests confirm the link’s reliability, achieving error-free data transmission at 3 Gb/s using on-off keying modulation.
2 November 2021 in Journal of Lightwave Technology
We present a photonically-excited antenna array at E-band for scanning by beam switching in wireless links. First, we discuss the proposed technique applied to photonic-enabled (sub)millimeter-wave transmitters. Next, we present our implementation; it consists of two sub-arrays of stacked patches as primary feeds of a Polytetrafluoroethylene (PTFE) lens, with one photodiode feeding each sub-array. To validate the assembly, the return loss and radiation patterns have been measured for one of the sub-arrays excited with a coplanar probe. In turn, the lens illuminated by one of the sub-arrays yields a directivity of 27 dBi. The radiation patterns measured for the transmitter module (including the lens) are in very good agreement with full-wave simulations, and they show that excitation of one of either sub-arrays allows beam switching between $\pm 2.7^\circ$ with a beam crossover at $-3\, \mathrm{dB}$ . Finally, we have tested the transmitter in a 0.6 m wireless link. Depending on the position of the detector and on which sub-array is excited, we have accomplished 5 Gbps transmission for on-off-keying modulation and direct detection (BER $=10^{-11}$ ). The system constitutes an initial proof of photonic-assisted beam switching for mm-wave transmitters enabling broadband operation with a directive and switchable beam.
This abstract describes the first design and assembly of a photonically-excited antenna at E-band for beam switching in millimeter-wave wireless links. The designed antenna consists of two arrays of stacked patches, with one photodiode feeding each array. The stacked patch provides an impedance bandwidth larger than 23 % and a stable radiation pattern over the E-band. The array is combined with a lens to increase the overall gain. Excitation of either patch array allows beam steering between ±2.7° for accurate beam alignment.
8 April 2021 in IEEE Transactions on Antennas and Propagation
This work presents an analytic model to derive the scan impedance of planar infinite phased arrays of dipoles at a dielectric interface when only the (0,0) Floquet mode propagates. The proposed model builds on the boundary conditions met by the fundamental Floquet mode at the interface to provide a novel derivation of the equivalent circuit for the scan impedance. The analysis is also extended to include the effect of a sufficiently thick grounded substrate that does not affect the elements current distribution and does not interact with the evanescent fields. Next, formulas for the ratio of intensity radiated towards each half-space for an interfacial array are provided. In a consecutive step, an asymptotic approximation is derived for the current distribution in arrays of arbitrary loaded dipoles, and the reactance of a dipole in the array environment is related to the inductance of a grid of wires. This model constitutes a useful tool to clearly identify the role of the different array variables (dipole dimensions, relative permittivity of the substrate, periodicity, end-load, and scan angle in the principal planes) on the scan impedance by simple expressions and equivalent circuits. The model predictions are in good agreement with full-wave simulations and with previously published works.