Phosphorus (P) is an essential nutrient for living organisms and cannot be replaced or substituted. In this paper, we present a simple yet efficient membrane free electrochemical system for P removal and recovery as calcium phosphate (CaP). This method relies on in situ formation of hydroxide ions by electro mediated water reduction at a titanium cathode surface. The in situ raised pH at the cathode provides a local environment where CaP will become highly supersaturated. Therefore, homogeneous and heterogeneous nucleation of CaP occurs near and at the cathode surface. Because of the local high pH, the P removal behavior is not sensitive to bulk solution pH and therefore, efficient P removal was observed in three studied bulk solutions with pH of 4.0 (56.1%), 8.2 (57.4%), and 10.0 (48.4%) after 24 h of reaction time. While P removal efficiencies are not generally affected by bulk solution pH, the chemical-physical properties of CaP solids collected on the cathode are still related to bulk solution pH, as confirmed by structure characterizations. High initial solution pH promotes the formation of more crystalline products with relatively high Ca/P molar ratio. The Ca/P molar ratio increases from 1.30 (pH 4.0) to 1.38 (pH 8.2) and further increases to 1.55 (pH 10.0). The formation of CaP precipitates was a typical crystallization process, with an amorphous phase formed at the initial stage which then transforms to the most stable crystal phase, hydroxyapatite, which is inferred from the increased Ca/P molar ratio from 1.38 (day 1) to the theoretical 1.76 (day 11) and by the formation of needle-like crystals. Finally, we demonstrated the efficiency of this system for real wastewater. This, together with the fact that the electrochemical method can work at low bulk pH, without dosing chemicals and a need for a separation process, highlights the potential application of the electrochemical method for P removal and recovery.

To address the issues of eutrophication and the potential risk of phosphorus (P) shortage, it is essential to remove and recover P from P-containing streams to close this nutrient cycle. Electrochemical induced calcium phosphate (CaP) precipitation was shown to be an efficient method for P recovery. However, the influence of natural organic matter (NOM) is not known for this treatment. In this paper, the behavior of NOM and its effect on CaP precipitation was studied. In contrast to studies where NOM hindered CaP precipitation, results show that the interaction of NOM with CaP improves the removal of P, independent of the types of NOM. The P removal at the average increased from 43.8 ± 4.9% to 58.5 ± 1.2% in the presence of 1.0 mg L-1 NOM. Based on the yellow color of the CaP product, NOM is co-precipitated. The bulk solution pH with and without buffers has totally different effects on the precipitation process. Without buffer, CaP precipitates on the cathode surface in a wide pH range (pH 4.0-10.0). However, the precipitation process is completely inhibited when the bulk solution is buffered at pH 4.0 and 6.0. This is probably due to neutralization of OH- by the buffers. Regardless of the presence or absence of NOM and solution pH, the recovered products are mainly amorphous CaP unless the electrolysis time was increased to seven days with 4.0 A m-2, in which crystalline CaP formed. These findings advance our understanding on the interaction of Ca, P and NOM species for the application of electrochemical method for P recovery from real wastewater.

Phosphonates are an important type of phosphorus-containing compounds and have possible eutrophication potential. Therefore, the removal of phosphonates from waste streams is as important as orthophosphate. Herein, we achieved simultaneously removal and recovery of phosphorus from nitrilotris (methylene phosphonic acid) (NTMP) using an electrochemical cell. It was found that the C-N and C-P bonds of NTMP were cleaved at the anode, leading to the formation of orthophosphate and formic acid. Meanwhile, the converted orthophosphate reacted with coexisting calcium ions and precipitated on the cathode as recoverable calcium phosphate solids, due to an electrochemically induced high pH region near the cathode. Electrochemical removal of NTMP (30 mg/L) was more efficient when dosed to effluent of a wastewater treatment plant (89% in 24 h) than dosed to synthetic solutions of 1.0 mM Ca and 50 mM Na2SO4 (43% in 168 h) while applying a current density of 28 A/m2 and using a Pt anode and Ti cathode. The higher removal efficiency of NTMP in real waste water is due to the presence of chloride ions, which resulted in anodic formation of chlorine. This study establishes a one-step approach for simultaneously phosphorus removal and recovery of calcium phosphate from non-orthophosphates.

Electrochemical wastewater treatment can induce calcium phosphate precipitation on the cathode surface. This provides a simple yet efficient way for extracting phosphorus from municipal wastewater without dosing chemicals. However, the precipitation of amorphous calcium phosphate (ACP) is accompanied by the precipitation of calcite (CaCO3) and brucite (Mg(OH)2). To increase the content of ACP in the products, it is essential to understand the precipitation sequence of ACP, calcite and brucite in electrochemical wastewater treatment. Given the fact that calcium phosphate (i.e., hydroxyapatite) has the lowest thermodynamic solubility product and highest saturation index in the wastewater, it has the potential to precipitate first. However, this is not observed in electrochemical phosphate recovery from raw wastewater, which is probably because of the very high Ca/P molar ratio (7.5) and high bicarbonate concentration in the wastewater result in formation of calcite. In case of decreased Ca/P molar ratio (1.77) by spiking external phosphate, most of the removed Ca in the wastewater was used for ACP formation instead of calcite. The formation of of brucite, however, was only affected when the current density was decreased, or the size of cathode was changed. Overall, the removal of Ca and Mg is much more affected by current density than the surface area of cathode, whereas for P removal, the reverse is true. Because of these dependencies, though there is no definite precipitation sequence among ACP, calcite and brucite, it is still possible to influence the precipitation degree of these species by relative low current density and high surface area or by targeting phosphorus-rich wastewaters.

The recovery of phosphorus (P) from high-strength acidic waste streams with high salinity and organic loads is challenging. Here, we addressed this challenge with a recently developed electrochemical approach and compared it with the chemical precipitation method via NaOH dosing. The electrochemical process recovers nearly 90% of P (∼820 mg/L) from cheese wastewater in 48 h at 300 mA with an energy consumption of 64.7 kWh/kg of P. With chemical precipitation, >86% of P was removed by NaOH dosing with a normalized cost of 1.34–1.80 euros/kg of P. The increase in wastewater pH caused by NaOH dosing triggered the formation of calcium phosphate sludge instead of condensed solids. However, by electrochemical precipitation, the formed calcium phosphate is attached to the electrode, allowing the subsequent collection of solids from the electrode after treatment. The collected solids are characterized as amorphous calcium phosphate (ACP) at 200 mA or a precipitation pH of ≥9. Otherwise, they are a mixture of ACP and hydroxyapatite. The products have sufficient P content (≤14%), of which up to 85% was released within 30 min in 2% citric acid and a tiny amount of heavy metals compared to phosphate rocks. This study paves the way for applying electrochemical removal and recovery of phosphorus from acidic P-rich wastewater and offers a sustainable substitute for mined phosphorus.

Phosphorus removal and recovery from waste streams are crucial to prevent eutrophication and sustain fertilizer production. As has been shown in our previous papers, electrochemical treatment has the potential to achieve this goal. However, the adoption of electrochemical approach is limited by its high energy consumption. Here, we investigate the possibility of electrochemical phosphorus removal at extremely low current density using graphite felt as the cathode. We found a current density as low as 0.04 A/m2 can enhance the removal of phosphate in our electrochemical system. The removal of phosphate at extremely low current density resulted from electrochemical induced calcium phosphate precipitation and not by electrochemical adsorption. Electrochemical treatment of real domestic wastewater at 0.2 A/m2 almost eliminates the precipitation of Mg(OH)2 and limits the formation of CaCO3. The recovered precipitates are dominated by calcium phosphate (59%), followed by 35% CaCO3 and 6% Mg(OH)2. The specific energy consumption of this newly electrochemical system is between 4.4 and 26.4 kW h/kg P, which is 2 orders of magnitude lower than our previous system (110-2238 kW h/kg P). Key factors for this improvement prove to be enlarged precipitation area and hydroxide flux retardation by graphite felt. Practically, our study offers a potential way to reduce the energy consumption in electrochemical removal of phosphate by using a graphite felt cathode and at a current density below 0.2 A/m2. Fundamentally, our study contributes to the understanding of adsorption and precipitation in electrochemical removal of phosphate at an extremely low current density and with carbon-based electrodes.