In this study, we investigated the catalytic performance of Ru nanoparticles (NPs) supported on Ni-nanowires for the first time. This appears to be a highly efficient catalyst for low-temperature methanation, e.g., ca. 100% conversion and 100% of CH4 selectivity can be achieved at ca. 179 °C, while the turnover frequency (TOF) value was 2479.2 h−1. At the same time, the onset of a reaction was observed at a temperature as low as 130 °C. The comparison of nano-Pd and nano-Ru supported on Ni-nanowires enabled us to prove that oxidized surface metals are highly important for the high activity of the investigated nano-Ru@nanowired-Ni. Moreover, similar to the microscopic Sabatier rule, which indicates that some optimal reactivity level of a catalyst exists, we showed that Ni-nanowires (a higher specific surface area than a standard metal surface, e.g., in the form of a metal foam, but lower than nano-sized materials) significantly enhances the performance of the Ru-Ni catalytic system.
1 December 2018 in Applied Catalysis B: Environment and Energy
Privileged structures is a term that is used in drug design to indicate a fragment that is popular in the population of drugs or drug candidates that are in the application or investigation phases, respectively. Privileged structures are popular motifs because they generate efficient drugs. Similarly, some elements appear to be more efficient and more popular in catalyst design and development. To indicate this fact, we use here a term privileged metal combination. In particular, Ru-based catalysts have paved a bumpy road in a variety of commercial applications from ammonia synthesis to carbon (di)oxide methanation. Here, we review Ru/Ni combinations in order to specifically find applications in environmental nanocatalysis and more specifically in carbon (di)oxide methanation. Synergy, ensemble and the ligand effect are theoretical foundations that are used to explain the advantages of multicomponent catalysis. The economic effect is another important issue in blending metal combinations. Low temperature and photocatalytic processes can be indicated as new tendencies in carbon (di)oxide methanation. However, due to economics, future industrial developments of this reaction are still questionable.
The paper introduces spatially stable Ni-supported bimetallic catalysts for CO2 methanation. The catalysts are a combination of sintered nickel mesh or wool fibers and nanometal particles, such as Au, Pd, Re, or Ru. The preparation involves the nickel wool or mesh forming and sintering into a stable shape and then impregnating them with metal nanoparticles generated by a silica matrix digestion method. This procedure can be scaled up for commercial use. The catalyst candidates were analyzed using SEM, XRD, and EDXRF and tested in a fixed-bed flow reactor. The best results were obtained with the Ru/Ni-wool combination, which yields nearly 100% conversion at 248 °C, with the onset of reaction at 186 °C. When we tested this catalyst under inductive heating, the highest conversion was observed already at 194 °C.
15 September 2023 in Chemical Engineering Research and Design
The paper presents an assessment of flotation efficiency in the separation of plastics from metals derived from printed circuit boards (PCBs). The PCBs were ground in a knife mill prior to flotation. The contact angles of various materials corresponding to the grains from ground PCBs were measured, and a series of flotation tests was carried out to obtain the best product. The impact of the following parameters were investigated: the reagent and its dose, the airflow rate through the flotation tank and the feed concentration. The highest efficiency of metal recovery from PCBs was achieved for Dimethoxy dipropyleneglycol at a concentration of 157 mg/dm3 and with an airflow of 200 dm3/h and a feed concentration of <50 g/dm3. In the hydrophilic product (concentrate), it was mainly Cu (40%) and Sn (7.8%) that were identified by means of XRF, but there were also trace amounts of precious metals such as Au (0.024%), Ag (0.5797%) and Pd (149 ppm). Impurities in the form of Si (5%), Ca (3.2) and Br (2.1) were also identified in this product. Small amounts of metals in their metallic form were identified in the hydrophobic product (waste), mainly Cu (2.3), Al (1.7) and Sn (1.1). As a result of the research, high recovery ratios were obtained for Cu (93%), Sn (84), Ag (83) and Au (69). The purity of obtained metal concentrate with this method was lower in comparison with the other methods of the recovery of metals from ground PCBs for the same feed, i.e. electrostatic or gravity separation. Also considering other factors such as the environmental impact of the flotation process, the number of facilities and their energy consumption, this process should not be used in the developed metal recovery technology. Using electrostatic separation for the same feed obtained much better results.