This paper deals with the effect of microstructure condition on ignition temperature, mechanical and corrosion properties of commercial WE43 alloy prepared by various processing techniques including conventional casting, extrusion, and powder metallurgy methods such as spark plasma sintering. For different processing technique, differences in microstructures were observed, including different grain sizes, intermetallic phases, amount of alloying elements in the solid solutions, or specific structural elements. Mechanical and corrosion properties were improved especially by grain refinement. Precipitation from oversaturated solid solutions led to further improvement of mechanical properties, while corrosion resistance was just slightly decreased due to the fine and homogeneously distributed precipitates of Mg₄₁Nd₅. The obtained results indicate huge differences in ignition resistance based on the metallurgical state of the microstructure. An improved ignition resistance was obtained at the condition with a higher concentration of proper alloying elements (Y, Nd, Gd, Dy) in the solid solution and absence of eutectic phases in the microstructure. Thermally stable intermetallic phases had a minor effect on resulting ignition temperature.

Zinc and its alloys belong to a group of biodegradable materials, which can be potentially used for the preparation of temporary orthopedic implants. The research of biodegradable zinc materials revealed a lot of limitations; however, the new processing approaches of those materials can enhance their properties, which are insufficient for now. In this study, the zinc composite with 8 wt.% of hydroxyapatite (Zn/HA8) prepared for the first time by extrusion process was characterized from the point of view of the structural, mechanical and corrosion properties. The extrusion process led to good integrity of the interfaces between the zinc and hydroxyapatite particles. Mechanical behavior confirmed the role of hydroxyapatite as a defect in the material structure, which led to a decrease of the Zn/HA8 mechanical properties by approximately 30% (compressive yield strength (CYS) = 154 MPa Zn, 113 MPa Zn/HA8). Despite that, the Zn/HA8 composite showed sufficient mechanical properties for cancellous bone replacement and reached the lower limit for cortical bone. Additionally, the presence of hydroxyapatite caused the preferential precipitation of hydroxyapatite (HA) from the solution and can lead to a significant enhancement of the tissue/implant interface interactions.

Two novel ignition-resistant magnesium alloys, Mg-2Gd-2Y-1Ca and Mg-2Nd-1Y-1Ca, were prepared in the ultrafine-grain condition by equal channel angular pressing (ECAP). In addition, four commercial alloys—AZ31, AX41, AE42 and WE43—were prepared similarly as a reference. The microstructure, mechanical properties and ignition temperature were thoroughly investigated. Both novel alloys exhibited a mean grain size of ~1 µm and dense distribution of small secondary phase particles. The mechanical strength measured by the tensile deformation test showed that the novel alloys are much stronger (~290 MPa) than all commercial alloys except WE43. However, Ca segregation into the grain boundaries caused a significant decrease in ductility (<6%). The ignition temperature of the novel alloys (~950 °C) was considerably improved by the presence of Gd/Nd, Y and Ca. This study showed that both novel alloys exhibit high strength and high ignition temperature in the ultrafine-grain condition.

Zinc and its alloys seem to be promising candidates for biodegradable applications. Those materials are often modified by other elements or compounds in order to enhance their properties. The combination of zinc and apatites is challenging for several reasons. However, the advantages connected with the biological aspects suggest the need for further research into such materials. In this study, three zinc-based composites with 4 and 8 wt. % of nanohydroxyapatite or nanomonetite (Zn-4MO, Zn-4HA, Zn-8HA) were prepared by sintering and subsequent extrusion. Materials prepared in this way were characterized from the microstructural, mechanical and corrosion point of view. The obtained results showed a significant influence of particle character (amount and morphology) on the strength and ductility of the prepared materials. In case of Zn-4MO, the presence of monetite significantly increased the ductility compared with the other materials. In addition, the increment of the degradation rate caused by the presence of monetite was observed as well. All obtained results pointed out to significant advantages of monetite for the preparation of Zn-apatite composites compared with hydroxyapatite.

The sectional fire ladders, made of aluminium alloy AA6063, belong to the basic equipment of the fire department of the Czech Republic. The use of these materials facilitates the deployment of ladders for firefighting, but it also brings with ...