Thrust vectoring innovations are demonstrated ideas that improve the projection of aerospace power with enhanced maneuverability, control effectiveness, survivability, performance, and stealth. Thrust vector control systems following a variety of concepts have been considered for modern aircraft and missiles to enhance their military performance. Short Take-off and Landing (STOL) and control effectiveness at lower aircraft speeds can be achieved by employing Fluidic Thrust Vectoring Control (FTVC). This paper summarizes a range of ideas for FTVC that have been designed and tested both computationally and experimentally to determine the thrust vectoring performance of supersonic propulsion system nozzles. The conventional method of thrust vectoring involves mechanical means to deflect the direction of flow of the exhaust gases, whereas the most recent method involves fluidic-based thrust vectoring techniques. Fluid-based thrust vectoring has the advantages of simplicity and low weight over mechanical-based thrust vectoring, which has complex geometry and adds extra weight to the aircraft. The fluidic vectoring control nozzles are divided into seven categories: shock vector, bypass shock vector, counterflow, co-flow, throat skewing, dual throat, and bypass dual throat nozzle control. This paper provides a summary of each fluidic thrust vectoring technique with its characteristics, design, classification, and different operational criteria developed to date and compares the intrinsic characteristics of each technique. Based on the present literature, it is concluded that among all the fluidic control techniques, the bypass dual-throat nozzle control can achieve better thrust vectoring performance with large vector angles and low thrust loss.

In this paper, we present the procedure of estimating the aerodynamic coefficients for a commercial aviation aircraft from geometric parameters at low-cruise-flight conditions using US DATCOM (United States Data Compendium) and XFLR software. The purpose of this research was to compare the stability parameters from both pieces of software to determine the efficacy of software solution for a wide-body aircraft at the stated flight conditions. During the initial phase of this project, the geometric parameters were acquired from established literature. In the next phase, stability and control coefficients of the aircraft were estimated using both pieces of software in parallel. Results obtained from both pieces of software were compared for any differences and the both pieces of software were validated with analytical correlations as presented in literature. The plots of various parameters with variations of the angle of attack or control surface deflection have also been obtained and presented. The differences between the software solutions and the analytical results can be associated with approximations of techniques used in software (the vortex lattice method is the background theory used in both DATCOM and XFLR). Additionally, from the results, it can be concluded that XFLR is more reliable than DATCOM for longitudinal, directional, and lateral stability/control coefficients. Analyses of a Boeing 747-200 (a wide-body commercial airliner) in DATCOM and XFLR for complete stability/control analysis including all modes in the longitudinal and lateral directions have been presented. DATCOM already has a sample analysis of a previous version of the Boeing 737; however, the Boeing 747-200 is much larger than the former, and complete analysis was, therefore, felt necessary to study its aerodynamics characteristics. Furthermore, in this research, it was concluded that XFLR is more reliable for various categories of aircraft alike in terms of general stability and control coefficients, and hence many aircraft can be dependably modeled and analyzed in this software.

Airfoil selection procedure, wind tunnel testing and an implementation of 6-DOF model on flying wing micro aerial vehicle (FWMAV) has been proposed in this research. The selection procedure of airfoil has been developed by considering parameters related to aerodynamic efficiency and flight stability. Airfoil aerodynamic parameters have been calculated using a potential flow solver for ten candidate airfoils. Eppler-387 proved to be the most efficient reflexed airfoil and therefore was selected for fabrication and further flight testing of vehicle. Elevon control surfaces have been designed and evaluated for longitudinal and lateral control. The vehicle was fabricated using hot wire machine with EPP styrofoam of density 50 Kg/ ${\mathrm{m}}^3$ . Static aerodynamic coefficients were evaluated using wind tunnel tests conducted at cruise velocity of 20 m/s for varying angles of attack. Rate derivatives and elevon control derivatives have also been calculated. Equations of motion for FWMAV have been written in a body axis system yielding a 6-DOF model. It was found during flight tests that vehicle conducted coordinated turns with no appreciable adverse yaw. Since FWMAV was not designed with a vertical stabilizer and rudder control surface, directional stability was therefore augmented through winglets and high wing leading edge sweep. Major problems encountered during flight tests were related to left rolling tendency. The left roll tendency was found inherent to clockwise rotating propeller as ‘P’ factor, gyroscopic precession, torque effect and spiraling slipstream. To achieve successful flights, many actions were required including removal of excessive play from elevon control rods, active actuation of control surfaces, enhanced launch speed during take off, and increased throttle control during initial phase of flight. FWMAV flew many successful stable flights in which intended mission profile was accomplished, thereby validating the proposed airfoil selection procedure, modeling technique and proposed design.

Modern aircraft and missiles are gradually integrating thrust vector control systems to enhance their military capabilities. Bypass Dual-Throat Nozzle (BDTN) control is a new fluidic thrust vectoring technique capable of achieving superior performance with large vector angles and low thrust loss. In this study, we analyzed the flow characteristics and performance parameters of BDTN by varying the bypass angle, nozzle convergence angle, and bypass width. The flow governing equations are solved according to a finite volume discretization technique of the compressible RANS equations coupled with the Renormalization Group (RNG) k-ϵ turbulence model for Nozzle Pressure Ratio (NPR = 2~10) to capture the significance of under-expanded and over-expanded jets. Results show that by decreasing the bypass angle from 90° to 35°, there is a 6% increase in vectoring angle while the vectoring efficiency is enhanced by 18%. However, a decrease of 3% in the thrust and discharge coefficients is also observed. When the convergence angle was increased from 22° to 37°, vectoring angle, discharge coefficient, and thrust coefficient increased by 2%, 1%, and 0.26%, respectively. Moreover, vectoring efficiency is also enhanced by 8% by reducing the convergence angle from 37° to 22°. Based on the investigated parameters, it is determined that nozzle convergence angle does not significantly influence thrust vectoring performance, however, bypass width and bypass angle have a significant effect on thrust vectoring performance.

In this research effect of propeller induced flow on aerodynamic characteristics of low aspect ratio flying wing micro aerial vehicle has been investigated experimentally in subsonic wind tunnel. Left turning tendencies of right-handed propellers have been discussed in literature, but not much work has been done to quantify them. In this research, we have quantified these tendencies as a change in aerodynamic coefficient with a change in advance ratio at a longitudinal trim angle of attack using subsonic wind tunnel. For experimental testing, three fixed pitch propeller diameters (5 inch, 6 inch and 7 inch), three propeller rotational speeds (7800, 10800 and 12300 RPMs) and three wind tunnel speeds (10, 15 and 20 m/s) have been considered to form up 27 advance ratios. Additionally, wind tunnel tests of 9 wind mill cases were conducted and considered as baseline. Experimental uncertainty assessment for measurement of forces and moments was carried out before conduct of wind tunnel tests. Large variation in lift, drag, yawing moment and rolling moment was captured at low advance ratios, which indicated their significance at high propeller rotational speeds and large propeller diameters. Side force and pitching moment did not reflect any significant change. $\frac {L}{D}$ at trim point was found a nonlinear function of propeller diameter to wingspan ratio $\frac {D}{b}$ , and propeller rotational speed. Rate and control derivatives were obtained using unsteady vortex lattice method with propeller induced flow effect modeled by Helical Vortex Modeling approach. In this research, we have proposed improved 6-DOF equations of motion, with a contribution of advance ratio $J$ . It is concluded, that propeller induced flow effects have a significant contribution in flight dynamic modeling for vehicles with large propeller diameter to wingspan ratio, $\frac {D}{b}$ of 22% or more.