Modern aircraft and missiles are gradually integrating thrust vector control systems to enhance their military capabilities. Bypass Dual-Throat Nozzle (BDTN) control is a new fluidic thrust vectoring technique capable of achieving superior performance with large vector angles and low thrust loss. In this study, we analyzed the flow characteristics and performance parameters of BDTN by varying the bypass angle, nozzle convergence angle, and bypass width. The flow governing equations are solved according to a finite volume discretization technique of the compressible RANS equations coupled with the Renormalization Group (RNG) k-ϵ turbulence model for Nozzle Pressure Ratio (NPR = 2~10) to capture the significance of under-expanded and over-expanded jets. Results show that by decreasing the bypass angle from 90° to 35°, there is a 6% increase in vectoring angle while the vectoring efficiency is enhanced by 18%. However, a decrease of 3% in the thrust and discharge coefficients is also observed. When the convergence angle was increased from 22° to 37°, vectoring angle, discharge coefficient, and thrust coefficient increased by 2%, 1%, and 0.26%, respectively. Moreover, vectoring efficiency is also enhanced by 8% by reducing the convergence angle from 37° to 22°. Based on the investigated parameters, it is determined that nozzle convergence angle does not significantly influence thrust vectoring performance, however, bypass width and bypass angle have a significant effect on thrust vectoring performance.

In this research effect of propeller induced flow on aerodynamic characteristics of low aspect ratio flying wing micro aerial vehicle has been investigated experimentally in subsonic wind tunnel. Left turning tendencies of right-handed propellers have been discussed in literature, but not much work has been done to quantify them. In this research, we have quantified these tendencies as a change in aerodynamic coefficient with a change in advance ratio at a longitudinal trim angle of attack using subsonic wind tunnel. For experimental testing, three fixed pitch propeller diameters (5 inch, 6 inch and 7 inch), three propeller rotational speeds (7800, 10800 and 12300 RPMs) and three wind tunnel speeds (10, 15 and 20 m/s) have been considered to form up 27 advance ratios. Additionally, wind tunnel tests of 9 wind mill cases were conducted and considered as baseline. Experimental uncertainty assessment for measurement of forces and moments was carried out before conduct of wind tunnel tests. Large variation in lift, drag, yawing moment and rolling moment was captured at low advance ratios, which indicated their significance at high propeller rotational speeds and large propeller diameters. Side force and pitching moment did not reflect any significant change. $\frac {L}{D}$ at trim point was found a nonlinear function of propeller diameter to wingspan ratio $\frac {D}{b}$ , and propeller rotational speed. Rate and control derivatives were obtained using unsteady vortex lattice method with propeller induced flow effect modeled by Helical Vortex Modeling approach. In this research, we have proposed improved 6-DOF equations of motion, with a contribution of advance ratio $J$ . It is concluded, that propeller induced flow effects have a significant contribution in flight dynamic modeling for vehicles with large propeller diameter to wingspan ratio, $\frac {D}{b}$ of 22% or more.

Landing gear system of an aircraft enables it to take off and land with safety and comfort. Because of the horizontal and vertical velocity of aircraft, upon landing, the complete aircraft undergoes different forcing functions in the form of the impact force that is absorbed by landing gears, shock absorbers, and actuators. In this research, a selection methodology has been proposed for an electrical actuator to be installed in the retraction mechanism of nose landing gear of an aircraft having 1600 kg gross takeoff weight. Nose landing gear and its associated components, like strut and shock absorbers, were modeled in CAD software. Analytical expressions were then developed in order to calculate the actuator stroke, translational velocity, force, and power for complete cycle of retraction, and some were subsequently compared with the computational results that were obtained using MSC ADAMS${}^{\circledR }$. Air in the oleo-pneumatic shock absorber of nose landing gear was modeled as a nonlinear spring with equivalent spring constant, whereas hydraulic oil was modeled as a nonlinear damper with equivalent damping constant. The nose landing gear system was modeled as a mass-spring-damper system for which a solution for sinusoidal forcing functions is proposed. Finally, an electrical actuator has been selected, which can retract and extend nose landing gear, meeting all of the constraints of aircraft, like fuselage space, aircraft ground clearance, locking loads, power consumption, retraction and extension time, and dynamic response of aircraft. It was found that the selection of an electrical actuator is based upon the quantification of forces transmitted to electrical actuator during one point load at gross takeoff weight. The ability of retraction and extension time, as dictated by Federal Aviation Regulation, has also been given due consideration in the proposed methodology as significant criteria. The proposed system is now in the process of ground testing, followed by flight testing in the near future.

In this research, a wide-body aircraft was analyzed with critical monitoring of its states, a function of several control inputs (wind gust, turbulence, and microburst). The aerodynamic and stability coefficients of a Boeing 747-200 were obtained from previously published works and 6- DOF equations were formulated. Simulations were conducted for various control inputs to determine the aircraft’s free response, as well as the forced response. In order to understand the nature of the atmosphere, three different models were incorporated, including (i) the Dryden Model, (ii) wind gust, and (iii) microburst. The aircraft was found to be stable in the longitudinal and lateral flight modes, with trim conditions agreeing with published data. For a vertical wind gust of −10 ft/s, the AoA and pitch rate were observed to oscillate sinusoidally and became stable with new trim conditions. These states were found to regain trim conditions once the gust was removed. In the case of 3D gust, it was found that the longitudinal modes achieved a new trim condition through Phugoid oscillations, whereas the lateral modes underwent short-period oscillations. For the case of turbulence, random fluctuations were observed for trim conditions with no unstable behavior. When considering the microburst case, it was found that the aircraft initially gained altitude in the region of the headwind; this was followed by a sharp descent under the influence of a vertical velocity component.