The IU characteristic curve of a photovoltaic module is affected by shadows, depending on the shaded area of the PV module, and the radiation received by the shaded areas. Another factor in the shape of the I-V curve of a PV module, is the configuration of the electrical connection between its cells and bypass diodes. Bypass diodes are installed in the modules to prevent power consumption when they are shaded or damaged; they also prevent cells from working near the avalanche zone. This paper examines the performance of a photovoltaic array. A PV array consists of modules connected between them. Particularly, the configuration with bypass diodes overlapped is analysed, showing that totally or partially shaded modules can consume some of the power generated by other modules of the PV array. This effect is also present in low power PV arrays. In these cases, the power dissipated by a diode is small; but if there are many diodes, the power dissipated by all the diodes can be comparable with the power produced by various PV modules. Additionally, this article deals with the influence of the inverter in the MPP tracking.

This research aimed to evaluate the thermal properties of new formulations of phase change materials (PCMs)-epoxy composites, containing a thickening agent and a thermally conductive phase. The composite specimens produced consisted of composites fabricated using (a) inorganic PCMs (hydrated salts), epoxy resins and aluminum particulates or (b) organic PCM (paraffin), epoxy resins, and copper particles. Differential Scanning Calorimetry (DSC) was used to analyze the thermal behavior of the samples, while hardness measurements were used to determine changes in mechanical properties at diverse PCM and conductive phase loading values. The results indicate that the epoxy matrix can act as a container for the PCM phase without hindering the heat-absorbing behavior of the PCMs employed. Organic PCMs presented reversible phase transformations over multiple cycles, an advantage that was lacking in their inorganic counterparts. The enthalpy of the organic PCM-epoxy specimens increased linearly with the PCM content in the matrix. The use of thickening agents prevented phase segregation issues and allowed the fabrication of specimens containing up to 40% PCM, a loading significantly higher than others reported. The conductive phase seemed to improve the heat transfer and the mechanical properties of the composites when present in low percentages (<10 wt %); however, given its mass, the enthalpy detected in the composites was reduced as their loading further increased. The conductive phase combination (PCM + epoxy resin + hardener + thickening agent) presents great potential as a heat-absorbing material at the temperatures employed.

Spain is a country with a high dependence on fossil fuels. For this reason, in 2007, it implemented a bonus system that aimed to encourage the production of renewable energies, particularly photovoltaic solar energy. These production bonuses, guaranteed by the Spanish government, led to an exponential increase in the number of companies in the market and, consequently, the MWh produced. However, in 2012, given the excessive budgetary burden involved in maintaining this “feed-in tariff” system and after several years of institutional instability, the aforementioned system of incentives for phoyovoltaic (PV) energy was eliminated. This paper has tried to analyze the consequences of this institutional change, a clear example of the “hold up” problem. For this purpose, a sample of 5354 companies, which was divided, geographically, into Spanish regions and, temporarily, into three different periods, has been taken, considering diverse economic and financial variables. The results show a notable weakening of the sector that, due to the effects of the regulatory change, has lost attractiveness and profitability for investors and is consequently suffering from stagnation, which has led to the disappearance of many companies in the sector.

Likert-scale surveys are the undeniable protagonists of online evaluations. They ask the respondent to express their degree of agreement with a series of statements related to the development of a subject. In contrast, in social networks, dichotomous surveys are mostly used. They force respondents to polarize their opinions by selecting “like” or “dislike”. This study compares the efficacy of binary and Likert surveys in gathering student opinions on mechanical engineering program subjects. Using Bayesian analysis, it analyzes the similarity of responses obtained from both formats. For each question and scale, the ratio of “I like” among the total responses collected was calculated. The Bayesian factor method was used to compare the ratios obtained. The null hypothesis was equality between the ratios obtained by the different scales for the same question. This hypothesis was rejected in only 7 of the 49 questions evaluated—less than 15%. Finally, the students were surveyed on the preference for use of both scales. More than 80% stated a preference for the use of the dichotomous format. In view of the results obtained, we recommend more frequent use of the dichotomous scale to gather students’ opinions.