Solvothermal synthesis is the most preferable preparation technique of metal–organic frameworks (MOFs) that consists of reactants mixing, ultrasonication, solvothermal reaction, product washing, and solvent evacuation. Owing to fast reaction kinetics in solvothermal reaction, this technique allows for production of uniform MOF particles with high crystallinity, high phase purity, and small particle sizes. However, it exhibits some difficulties of washing processes that may involve the blockage of pores due to incomplete removal of reactive medium from MOF products. The present study proposes an improvement of washing processes by introducing centrifugal separations with optimized parameters at two different stages: after reaction and after product washing. Nickel-based MOF-74 was synthesized as the experimental material for this purpose. The quality of the produced sample was evaluated by gas adsorption performance using CO2 at 1 bar and 25 °C. The final sample of the optimized synthesis routes was able to adsorb 5.80 mmol/g of CO2 uptake, which was competitive with literature data and significantly higher than the sample of the basic synthesis. Fourier-transform infrared spectroscopy (FTIR) and powder X-ray diffraction (PXRD) analysis revealed that the sample displayed much higher crystallinity structure and was clean from impurities after centrifugations. The outcome indicated the success of separation between MOF products and reactive medium during washing processes, leading to the effective pore activation of MOFs.
29 June 2020 in Physical Chemistry Chemical Physics
The accessibility of smectite interlayer spacing for the entry of CH 4 and CO 2 molecules significantly increases gas adsorption capacity in comparison to clays in a fully collapsed state.
The textural properties of synthetic and natural clays in the sodium form and exchanged with tetramethylammonium cations (TMA+) were characterized using N2 and Ar physisorption isotherms at cryogenic temperatures. Specific surface areas and micro/mesoporous volumes were determined using the BET and the t-plot models. The t-plot analysis requires the use of reference isotherms measured at the same temperature on the surface of non-porous materials with an identical chemical composition. In order to better assess the effects of chemical heterogeneities in the clay particles, reference isotherms representative of silica surfaces were taken into account in the analysis of the t-curve and corrected to account for variations in curvature at the interface of the film adsorbed in the micropores. In addition, high-resolution Ar adsorption isotherms at 87 K were analyzed using the Derivative Isotherm Summation (DIS) method to quantify the energy contributions of adsorption sites and determine the fractions of basal and lateral surfaces of clay particles. The high-energy adsorption sites, identified in the low-pressure range, were attributed to intra-particle microporosity due to stacking defects and/or open inter-layer spaces. These sites were differentiated from those on the lateral and basal surfaces of the particles. A modification of the DIS method was proposed to measure these contributions and improve the fit with the experimental data. The results show that TMA+ cation exchange significantly increases the microporosity of clays compared to their sodic form, which can be attributed to the increased contribution of intra-particle adsorption sites due to interlayer expansion.
HKUST-1 is a metal-organic framework (MOF) that is widely studied as an adsorbent for CO2 capture because of its high adsorption capacity and good CO2/CH4 selectivity. However, the numerous synthesis routes for HKUST-1 often result in the obtention of MOF in powder form, which limits its application in industry. Here, we report the shaping of HKUST-1 powder via the extrusion method with the usage of bio-sourced polylactic acid (PLA) as a binder. The characterization of the composite was determined by XRD, FTIR, TGA and SEM analyses. The specific surface area was determined from the N2 adsorption isotherm, whereas the gas adsorption capacities were investigated via measurements of CO2 and CH4 isotherms of up to 10 bar at ambient temperature. The material characterization reveals that the composite preserves HKUST-1’s crystalline structure, morphology and textural properties. Furthermore, CO2 and CH4 adsorption isotherms show that there is no degradation of gravimetric gas adsorption capacity after shaping and the composite yields a similar isosteric adsorption heat as pristine HKUST-1 powder. However, some trade-offs could be observed, as the composite exhibits a lower bulk density than pristine HKUST-1 powder and PLA has no impact on pristine HKUST-1’s moisture stability. Overall, this study demonstrates the possibility of shaping commercial HKUST-1 powder, using PLA as a binder, into a larger solid-state-form adsorbent that is suitable for the separation of CO2 from CH4 with a well-preserved pristine MOF gas-adsorption performance.
The mass and energy balances of a zero-dimensional model for hydrogen storage by adsorption is studied. The model is solved with an in-house MATLAB code and validated with three experimental case studies from the literature, obtained with cryogenic lab-scale reservoirs using different adsorbents and dynamic operating conditions. The results of the simulations agree well with reported measured temperature and pressure profiles. The hydrogen adsorption process is described assuming instantaneous thermodynamic equilibrium. In accordance with the potential theory, variations in the adsorbed phase volumes filling the adsorbent pores were described applying the revisited Dubinin–Astakhov (rev-D-A) equation and accounting for gas phase non-ideality. The simulation model was used to assess the energy requirements of a variety of adsorption-based hydrogen storage processes and compared with other conventional hydrogen storage modes such as compression and liquefaction. Thus, whatever different adsorbent materials are considered, this technology appears relatively energy intensive due to the reservoir cooling duty at cryogenic temperature.
HKUST−1 is an MOF adsorbent industrially produced in powder form and thus requires a post-shaping process for use as an adsorbent in fixed-bed separation processes. HKUST−1 is also sensitive to moisture, which degrades its crystalline structure. In this work, HKUST−1, in the form of crystalline powder, was extruded into pellets using a hydrophobic polymeric binder to improve its moisture stability. Thermoplastic polyurethane (TPU) was used for that purpose. The subsequent HKUST−1/TPU extrudate was then compared to HKUST−1/PLA extrudates synthesized with more hydrophilic polymer: polylactic acid (PLA), as the binder. The characterization of the composites was determined via XRD, TGA, SEM-EDS, and an N2 adsorption isotherm analysis. Meanwhile, the gas-separation performances of HKUST−1/TPU were investigated and compared with HKUST−1/PLA from measurements of CO2 and CH4 isotherms at three different temperatures, up to 10 bars. Lastly, the moisture stability of the composite materials was investigated via an aging analysis during storage under humid conditions. It is shown that HKUST−1’s crystalline structure was preserved in the HKUST−1/TPU extrudates. The composites also exhibited good thermal stability under 523 K, whilst their textural properties were not significantly modified compared with the pristine HKUST−1. Furthermore, both extrudates exhibited larger CO2 and CH4 adsorption capacities in comparison to the pristine HKUST−1. After three months of storage under atmospheric humid conditions, CO2 adsorption capacities were reduced to only 10% for HKUST−1/TPU, whereas reductions of about 25% and 54% were observed for HKUST−1/PLA and the pristine HKUST−1, respectively. This study demonstrates the interest in shaping MOF powders by extrusion using a hydrophobic thermoplastic binder to operate adsorbents with enhanced moisture stability in gas-separation columns.