Malte Frövel

Dr. Malte Frövel

orcid

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2003 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
IFI. Fernández
I. Fernández
FBF. Blas
F. Blas
MFMalte Frövel
Malte Frövel

1 June 2001 in Smart Materials and Structures
Verified
Journal Article
Closed access
PDF file
Alfredo GüemesAlfredo Güemes
Alfredo Güemes
JMJ M Menendez
J M Menendez
MFMalte Frövel
Malte Frövel
IFI Fernandez
I Fernandez
JPJ M Pintado
J M Pintado

18 July 2023 in Sensors
Verified
Journal Article
Open access
PDF file
Ana Fernández-MedinaAna Fernández-Medina
Ana Fernández-Medina
MFMalte Frövel
Malte Frövel
RHRaquel López Heredero
Raquel López Heredero
TBTomas Belenguer
Tomas Belenguer
ATAntonia de la Torre
Antonia de la Torre
AÁAlberto Álvarez-Herrero
Alberto Álvarez-Herrero
A composite optical bench made up of Carbon Fiber Reinforced Polymer (CFRP) skin and aluminum honeycomb has been developed for the Tunable Magnetograph instrument (TuMag) for the SUNRISE III mission within the NASA Long Duration Balloon Program. This optical bench has been designed to meet lightweight and low sensitivity to thermal gradient requirements, resulting in a low Coefficient of Thermal Expansion (CTE). In addition to the flight model, a breadboard model identical to the flight one has been manufactured, including embedded fiber Bragg temperature and strain sensors. The aim of this is to explore if the use of distributed fiber Bragg gratings (FBGs) can provide valuable information for strain and temperature mapping of an optical instrument on board a space mission during its operation as well as its on-ground testing. Furthermore, surface-mounted strain FBG sensors and thermocouples have been installed in the optical bench for intercomparison purposes. This paper presents the results obtained from a thermal vacuum test consisting of three thermal cycles with stabilization steps at 100 °C, 60 °C, 20 °C and −20 °C. Experimental results provide information about how FBG embedded temperature sensors can provide a proper and quick response to the temperature changes of the optical bench and that embedded FBG strain sensors are able to measure micro-deformation induced in a close-to-zero CTE optical bench.

1 March 2015 in NDT & E International
Verified
Journal Article
Open access
PZPablo Zuluaga-Ramírez
Pablo Zuluaga-Ramírez
MFMalte Frövel
Malte Frövel
TBTomás Belenguer
Tomás Belenguer
FSFélix Salazar
Félix Salazar
This work presents the evaluation of a new non-contact technique to assess the fatigue damage state of CFRP structures by measuring surface roughness parameters. Surface roughness and stiffness degradation have been measured in CFRP coupons cycled with constant amplitude loads, and a Pearson׳s correlation of 0.79 was obtained between both variables. Results suggest that changes on the surface roughness measured in strategic zones of components made of the evaluated CFRP, could be indicative of the level of damage due to fatigue loads. This methodology could be useful for other FRP due to similarities in the fatigue damage process

9 September 2021 in Sensors
Verified
Journal Article
Open access
PDF file
MVMiguel González del Val
Miguel González del Val
JMJulio Mora
Julio Mora
PGPaloma García
Paloma García
MFMalte Frövel
Malte Frövel
Icing is a hazard which is important for the aerospace industry and which has grown over the last few years. Developing sensors that can detect the existence not only of standard icing conditions with typically small droplet size, but also of Supercooled Large Droplet (SLD) conditions is one of the most important aims in order to minimize icing hazards in the near future. In the present paper a study of the Fiber Bragg Grating Sensors’ (FBGSs) performance as a flight icing detection system that predicts the conditions of an icing cloud is carried out. The test matrix was performed in the INTA Icing Wind Tunnel (IWT) with several icing conditions including SLD. Two optic fibers with 16 FBGS in total were integrated in the lower and upper surface of an airfoil to measure the temperature all over the chord. The results are compared with a Messinger heat and mass balance model and the measurements of the FBGS are used to predict the Liquid Water Content (LWC) and Ice Accretion Rate (IAR). Finally, the results are evaluated and a sensor assessment is made. A good correlation was observed between theoretical calculations and test results obtained with the FBGS in the IWT tests. FBGS proved to detect the beginning and end of ice accretion, LWC and IAR quickly and with good precision.

22 March 2018 in Structural Health Monitoring
Verified
Journal Article
Closed access
FTFelix Terroba
Felix Terroba
MFMalte Frövel
Malte Frövel
RARicardo Atienza
Ricardo Atienza
Aerial target drones are an important tool for the training of anti-air batteries and missiles for defense and homeland protection. These target drones are highly loaded structures that require a reliable inspection after each flight. A health and usage monitoring system based on load path changes has been developed. These changes are measured with fiber optic Bragg grating sensors which have been implemented in high loaded structural parts of the fuselage of the DIANA I-A, which is operated by the Spanish National Institute for Aerospace Technology. The health and usage monitoring system has been tested and calibrated by destructive tests, introducing defined damages in fuselage stringers and evaluating the structural damage by the measured strain distribution. The tests have shown that a simple system based on four fiber optic Bragg grating sensors is able to detect barely visible structural damages in the entire high loaded front fuselage of the drone. The health and usage monitoring system requires only on-ground equipment and enables a fast turnaround of the drone after each flight. Two DIANAs have been instrumented for their application in service. First flight tests have been performed and the performance of the health and usage monitoring system has been evaluated.