To achieve the goal of robust mechanical properties, long-term adhesion, sensitive electrical conductivity, the wearable sensors were inspired by various mussels on the base of catechol and its analogues.
A multifunctional microwave absorber with high thermal conductivity for 5G base station packaging comprising silylated GO/FeSiAl epoxy composites were fabricated by a simple solvent-handling method, and its microwave absorption properties and thermal conductivity were presented. It could act as an applicable microwave absorber for highly integrated 5G base station packaging with 5G antennas within a range of operating frequency of 2.575–2.645 GHz at a small thickness (2 mm), as evident from reflection loss with a maximum of −48.28 dB and an effective range of 3.6 GHz. Such a prominent microwave absorbing performance results from interfacial polarization resonance attributed to a nicely formed GO/FeSiAl interface through silylation. It also exhibits a significant enhanced thermal conductivity of 1.6 W/(mK) by constructing successive thermal channels.
24 June 2018 in International Journal of Polymer Science
Microspheres have excellent sealing performances such as injectivity, bridging-off, deep migration, and deformation performances, but their plugging effects are limited by the fast swelling rate and poor viscoelasticity. In this study, we synthesized a novel modified microsphere with polymerizable surfactant monomers and cationic monomers. We investigated the influence factors on the swelling performance and rheological properties of the microspheres and explored the ways to improve the plugging performance of hydrophobic-associating microspheres. The association behaviors in aqueous media of poly(acrylamide-co-methacry loyloxyethyl trimethyl ammonium chloride-co-n-dodecyl poly(etheroxy acrylate) P(AM-DMC-DEA) are proven to be mediated by the DEA content. Moreover, the hydrophobic association interaction has a strong effect on the performance of microspheres such as swelling properties, the rheological performance, and plugging properties. The swelling properties of microsphere studies exhibited the slow swelling rate. The rheological performance measurements showed significant improvements; yield stress, and creep compliance increased rapidly from 404 to 2060 Pa and 3.89 × 10−4 to 1.41 × 10−2 1/Pa, respectively, with DEA content in microspheres rising from 0.0% to 0.22%. The plugging properties of microspheres were enhanced by the slow swelling performance and good viscoelasticity.
7 November 2018 in International Journal of Polymer Science
A series of surfactive amphiphilic polymer PAADs were prepared from the copolymerization of sodium acrylate, dodecyl polyoxyethylene acrylate (DPA, a surfmer), and acrylamide under the action of a mixed initiating agent consisting of ammonium persulfate-sodium bisulfite/2,2-azobis[2-(2-imidazolin-2-yl) propane] dihydrochloride. The aggregative behaviors of PAADs were explored by 13C nuclear magnetic resonance, a viscometer, and a surface tension instrument. It was found that the apparent viscosity and surface activity of PAADs were significantly improved by the increase of average sequence length of hydrophobic micro blocks, strong intermolecular hydrophobic association, or the formation of mixed micelles between hydrophobic micro blocks and micromolecular surface-active agent. The introduction of long-chain alkyls on molecular chains prolonged the average sequence length of hydrophobic micro blocks in molecular chains and enhanced the hydrophobic association between molecular chains and the tight arrangement of molecular chains on water surfaces, thereby increasing the surface activity. Moreover, the anionic monomer sodium acrylate on molecular chains, via electrostatic repulsion, promoted the conversion from intrachain association to intermolecular association and thereby facilitated the formation of dense interfacial films, enhancing the surface activity of water solutions. Then, the anion surfmer sodium dodecylbenzenesulfonate interacted with the hydrophobic micro blocks on the molecular chains to form mixed micelles, which accelerated the interchain association and enhanced the polymer surface activity. The novel polymeric micelle with higher viscosifying ability and surface activity was expected to be a promising oil drive agent for tertiary oil recovery.
Linear diepoxide-terminated poly(ethylene glycol) (PEG) of molar mass 600, 1000 and 2000 g mol−1 was end-linked with dendrimer-star polymer (PAMAM) of generations 1.0 in water to prepare architecturally well-defined copolymer hydrogels. The structures and properties of the products were characterized using infrared, 1H NMR, DSC measurements, scanning electron microscopy (SEM) and swelling behavior tests. The swelling behavior of these hydrogels was tested in distilled water at constant temperature and the equilibrium swelling ratio (ESR) was determined for structurally different hydrogels and various environmental conditions, which showed that ESR was influenced by the molecular weight of PEG, the molar ratio of H amine groups/epoxy groups, temperature and pH. Higher ESR was obtained for either longer-chain PEG, non-stoichiometric H amine/epoxy groups ratio, acidic pH or lower temperatures. When the hydrogel was switched from 10 °C to 65 °C and pH 3.5 to 11.5, the swelling behavior of the hydrogels showed good reversibility for swelling–deswelling. When the molecular weight of PEG was changed in the range of 600–2000, the lower critical solution temperature (LCST) of hydrogel increased from 30 to 40 °C. When the molar ratio of H amine/epoxy groups was changed, the LCST was not significantly changed.
18 May 2020 in Journal of Inorganic and Organometallic Polymers and Materials