PH responsive chitosan and 3-Glycidyloxypropyl trimethoxysilane (GPTMS) hydrogels were synthesized by the sol-gel crosslinking reaction. GPTMS was introduced to influence several behaviors of the chitosan hydrogels, such as the swelling ratio, mechanical properties, swelling thermodynamics, kinetics, and expansion mechanism. The functional groups of Chitosan/GPTMS hybrid hydrogels were verified by FT-IR spectrometer. Differential scanning calorimetry (DSC) and the thermogravimetric analysis (TGA) were used to analyzed the thermal behavior of water molecules, the expansion of thermodynamics, and the content of water molecules in the hydrogel. The results show that hydrogel consists of 50 wt.% GPTMS (CG50) and has good mechanical properties and sensitivity to pH response characteristics in the acidic/alkaline buffer solution. The increase of GPTMS content leads to the increase of hydrophobic groups in the hydrogel and causes the decrease of the overall water content and the freezing bond water content. When the hydrogels were immersed in acid solution, the interaction force parameter was smaller than that of DI-water and alkaline. It means that the interaction forces between hydrogel and water molecules are relatively strong. The swelling kinetics of hybrid hydrogels were investigated to inspect the swelling mechanism. The result is consistent with the Fisk’s diffusion mechanism, meaning that the rate of water penetration is adjustable. The biodegradable hydrogel (CG50) in this study has good environmental sensitivity and mechanical properties. It is suitable to be applied in the fields of drug release or biomedical technology.

Thermal and dielectric properties of rigid-rod bifunctional epoxy resin 4,4-bis(2,3-epoxypropoxy) biphenyl epoxy (BP) and commercial epoxy resin diglycidyl ether of bisphenol A (DGEBA) were studied using differential scanning calorimeter (DSC), thermogravimetric analyzer (TGA), dynamic mechanical analyzer (DMA), thermal mechanical analyzer (TMA) and dielectric analyzer (DEA). These two epoxies were cured with cyanate ester hardener 2,2’-bis(4-cyanatophenyl) propane (AroCy B10). The BP/B10 system consisting of a rigid-rod structure exhibited better thermal properties than the DGEBA/B10 system with a flexible structure. Anisotropic BP/B10 (2:1) had the highest 5% weight loss temperature, the highest amount of residue and a smaller thermal expansion coefficient than the commercial DGEBA/B10 system. The BP/B10 system, which cured at the LC phase temperature, had higher Tg than the commercial DGEBA/B10 system, as found from dynamic mechanical analysis. The BP/B10 system also demonstrated better dielectric properties than the commercial DGEBA/B10 system when enough curing agent was provided.

Mesoporous tungsten trioxide (WO₃) films are prepared by the combination of the template-assisted sol-gel method and ultrasonic spraying deposition (USD) for supercapacitors, and then the surface morphology and electrochemical performance of the films are studied. Compared to WO₃ prepared by the traditional hydrothermal synthesis and spin coating method, the films obtained by USD exhibit advantages such as low cost, minimal material usage, and suitability for large-area in-line manufacturing. Additionally, the mesoporous structure of USD-produced films is also supportive of ion transportation. Due to the high specific surface area of WO₃ films deposited by USD, it is a material capable of use in a high-performance energy storage device. Through the control of spray coats, the film thickness and specific capacitance can be effectively controlled. Electrochemical measurements show that the mesoporous WO₃ films possess excellent electrochemical performance with a maximum specific capacitance of 109.15 F/g at 0.5 A/g. The cycling performance up to 5000 cycles of mesoporous WO₃ films is due to the stable nature of nanocrystalline produced by the combination of USD and sol-gel chemistry.

Chenopodium formosanum (CF), rich in nutrients and antioxidants, is a native plant in Taiwan. During the harvest, the seeds are collected, while the roots, stems, and leaves remain on the field as agricultural waste. In this study, di(phenyl)-(2,4,6-trinitrophenyl)iminoazanium (DPPH) radical scavenging ability and 2,2′-azino-bis(3-ethylbenzthiazoline-6-sulfonic acid) (ABTS) radical scavenging ability experiments of seeds, leaves, stems, and roots were designed using the Taguchi method (TM) under three conditions: Ethanol concentration (0–100%), temperature (25–65 °C), and extraction time (30–150 min). The result demonstrates that seeds and leaves have higher radical scavenging ability than stems and roots. Many studies focused on CF seeds. Therefore, this study selected CF leaves and optimized DPPH, ABTS, total phenol content (TPC), total flavonoid content (TFC), and reducing power (RP) through TM, showing that the predicted value of the leaf is close to the actual value. The optimized results of CF leaves were DPPH 85.22%, ABTS 46.51%, TPC 116.54 µg GAE/mL, TFC 143.46 µg QE/mL, and RP 23.29 µg VCE (vitamin C equivalent)/mL. The DPPH and ABTS of CF leaves were second only to the results of CF seeds. It can be seen that CF leaves have the potential as a source of antioxidants and help in waste reduction.