Plavka Skakun

Dr. Plavka Skakun


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 October 2020 in Metals
Verified
Journal Article
Open access
PDF file
LBLucijano Berus
Lucijano Berus
PSPlavka Skakun
Plavka Skakun
Dragan RajnovicDragan Rajnovic
Dragan Rajnovic
PJPetar Janjatovic
Petar Janjatovic
LSLeposava Sidjanin
Leposava Sidjanin
Mirko FickoMirko Ficko
Mirko Ficko
This paper presents a novel approach for edge detection and concatenation. It applies the proposed method on a set of optical microscopy images of aluminium alloy Al 99.5% (ENAW1050A) samples with different grain size values. The performance of the proposed approach is evaluated based on the intercept method and compared with the manual grain size determination method. Edge detection filters have proven inefficient in grain boundaries’ detection of the presented microscopy images. To some extent only the Canny edge-detection filter was able to compute grain boundaries of lower-resolution images adequately, while the presented method proved to be superior, especially in high-resolution images. The proposed method has proven its applicability, and it implies higher automatisation and lower processing times compared to manual optical microscopy image processing.

30 April 2020 in Metals
Verified
Journal Article
Open access
PDF file
PSPlavka Skakun
Plavka Skakun
Dragan RajnovicDragan Rajnovic
Dragan Rajnovic
PJPetar Janjatovic
Petar Janjatovic
SBSebastian Balos
Sebastian Balos
Andrei ShishkinAndrei Shishkin
Andrei Shishkin
LSLeposava Sidjanin
Leposava Sidjanin
In this study, an experimental, metallographic method for determining strain distribution in a cold extruded aluminum gear-like element, based on the dependence of recrystallized grain size on prior deformation, was devised in order to overcome design problems in manufacturing of complex parts where critical values of strain and stress could cause a fracture. The method was applied on a 99.5% aluminum bar subjected to cold, radial extrusion, in order to produce complex gear-like element. To reveal the strain and stress distribution in specimens, the calibration and flow curves were first obtained by uniaxial compression (Rastegaev test). Afterwards, the grain size in different parts of the gear section was examined, the strain and stress distributions were calculated, and the results were confirmed by microhardness measurements. It was found that grain size, strain, stress, and microhardness considerably differed throughout the cross-section of the gear. The coarsest grain, and thus the lowest strain zone, was obtained in the central part of the tooth and in the zone between teeth. Conversely, the finest grains appeared in the highest strain zone at the specimen surface, particularly in the root of the teeth. Furthermore, results were supported by microhardness measurements, i.e., microhardness corresponded to grain size and strain hardening. Finally, the real view of material flow in the complex extruded part was successfully obtained by the metallographic method.

1 January 2024
Verified
Conference Paper
Closed access
PSPlavka Skakun
Plavka Skakun
PJPetar Janjatovic
Petar Janjatovic
MDMiroslav Dramicanin
Miroslav Dramicanin
Dragan RajnovicDragan Rajnovic
Dragan Rajnovic

1 October 2018 in Tehnicki vjesnik - Technical Gazette
Verified
Journal Article
Open access
PDF file
PSPlavka Skakun
Plavka Skakun
RLRobert Lengyel
Robert Lengyel
SBSebastian Balos
Sebastian Balos
DMDejan Movrin
Dejan Movrin
MMMladomir Milutinović
Mladomir Milutinović
When divided material flow is enabled during extrusion process, the required forming load is lower compared to a conventional process. The reduction of forming load leads to higher quality of extruded part and longer tool life. One way...