This paper presents a novel broadband rectenna for ambient wireless energy harvesting over the frequency band from 1.8 to 2.5 GHz. First of all, the characteristics of the ambient radio-frequency energy are studied. The results are then used to aid the design of a new rectenna. A novel two-branch impedance matching circuit is introduced to enhance the performance and efficiency of the rectenna at a relatively low ambient input power level. A novel broadband dual-polarized cross-dipole antenna is proposed which has embedded harmonic rejection property and can reject the second and third harmonics to further improve the rectenna efficiency. The measured power sensitivity of this design is down to -35 dBm and the conversion efficiency reaches 55% when the input power to the rectifier is -10 dBm. It is demonstrated that the output power from the proposed rectenna is higher than the other published designs with a similar antenna size under the same ambient condition. The proposed broadband rectenna could be used to power many low-power electronic devices and sensors and found a range of potential applications.

A novel six-band dual circular polarization (CP) rectenna for ambient radio frequency (RF) energy harvesting is presented. Due to the nonlinearity and complex input impedance of the rectifying circuit, the design of a multiband and/or broadband rectenna is always challenging and its performance can be easily affected by variation in the input power level and load. Therefore, an improved impedance matching technique is introduced, which is aimed to improve the performance of the rectifier with a varying condition. A broadband dual CP receiving antenna is proposed, which has a very wide bandwidth (from 550 to 2.5 GHz) and a compact size. An annular ring structure and a novel feeding technique are employed in order to reduce the size and improve the antenna performance. As a result, the proposed rectenna is the first design that covers six frequency bands, including part of the digital TV and most cellular mobile and WLAN bands in the U.K., while the optimal load range for a constant conversion efficiency is from 10 to 75 kΩ. The measured results show that the maximum harvested dc power of the rectenna in typical outdoor and indoor environments are 26 and 8 μW, respectively; it can therefore be applied to a range of low-power wireless applications.

Impedance matching networks for nonlinear devices such as amplifiers and rectifiers are normally very challenging to design, particularly for broadband and multiband devices. A novel design concept for a broadband high-efficiency rectenna without using matching networks is presented in this paper for the first time. An off-center-fed dipole antenna with relatively high input impedance over a wide frequency band is proposed. The antenna impedance can be tuned to the desired value and directly provides a complex conjugate match to the impedance of a rectifier. The received RF power by the antenna can be delivered to the rectifier efficiently without using impedance matching networks; thus, the proposed rectenna is of a simple structure, low cost, and compact size. In addition, the rectenna can work well under different operating conditions and using different types of rectifying diodes. A rectenna has been designed and made based on this concept. The measured results show that the rectenna is of high power conversion efficiency (more than 60%) in two wide bands, which are 0.9-1.1 and 1.8-2.5 GHz, for mobile, Wi-Fi, and ISM bands. Moreover, by using different diodes, the rectenna can maintain its wide bandwidth and high efficiency over a wide range of input power levels (from 0 to 23 dBm) and load values (from 200 to 2000 Ω). It is, therefore, suitable for high-efficiency wireless power transfer or energy harvesting applications. The proposed rectenna is general and simple in structure without the need for a matching network hence is of great significance for many applications.

A comprehensive review of metamaterials and metasurfaces for wireless power transfer (WPT) and wireless energy harvesting (WEH) is presented in this article. According to the features of the electromagnetic field from the source to the receiver, WPT is divided into nonradiative near-field technology and radiative (near and far-field) technologies. Many different and important designs are reviewed and compared. It is shown that metamaterials and metasurfaces can significantly improve the power transfer efficiency and operational distance for WPT systems. They can also improve the energy conversion efficiency of wireless energy harvesters by making the reception less sensitive to incident wave angle and polarization. A rectenna is a critical element for both WPT and WEH. It is shown that metamaterial-based rectennas can achieve a higher RF to dc conversion efficiency. Furthermore, metamaterials can also be used as either parasitic elements or loading components to improve WEH performance in terms of circuit size, beamwidth, and conversion efficiency. Future development directions and opportunities of metamaterials and metasurfaces for WPT and WEH are also proposed in this article.

Condition monitoring for overhead power lines is critical for power transmission networks to improve their reliability, detect potential problems in the early stage, and ensure the utilization of the transmitting full capacity. Energy harvesting can be an effective solution for autonomous self-powered wireless sensors. In this paper, a novel bow-tie-shaped coil is proposed, which is placed directly under overhead power lines to scavenge the magnetic field energy. Compared to the conventional method by mounting the energy harvester on the power lines, this approach provides more flexibility and space to power bigger sensors such as the weather station. As the harvesting coil cannot entirely enclose the power lines, the demagnetization factor that is closely related to the core geometry should be considered and optimized. Thus a new bow-tie-shape core is designed to produce a much lower demagnetization factor (hence more power) than that of the conventional solenoid. The selection of core material is studied and found that Mn-Zn ferrite is the most suitable core material because it greatly reduces the eddy current losses and also has high permeability. Experiment results show that the bow-tie coil could have a power density of 1.86 μW/cm ³ when placed in a magnetic flux density of 7 μT _rms . This value is 15 times greater than the reported results under the same condition. If a longer bow-tie coil with more turns is placed in a magnetic flux density of 11μT _rms , the produced power density is 103.5 μW/cm ³ , which is comparable to a solar panel working during a cloudy day. Thus, the proposed solution is a very efficient and attractive method for harvesting the magnetic field energy for a range of monitoring applications.

Real-time data of high-voltage infrastructures collected by wireless sensors are the foundation of many smart grid applications. Energy harvesting can be an effective solution for autonomous, self-powered wireless sensors. In this paper, a coil with a novel helical core is proposed and optimized to scavenge the magnetic field energy efficiently near equipment carrying large currents. Due to the special design of the helical core, the path of the magnetic flux inside the core can be significantly increased, which leads to a reduction of the demagnetizing field. Therefore, the proposed core can generate a much higher flux density (hence more power) compared with conventional designs. The selection of the core material is studied and itis found that high permeability ferrite is the most suitable material. Experimental results show that the proposed helical coil with only 400 turns of wire can have a power density of 2.1 μW/cm ³ when placed in a magnetic flux density of 7 μTrm s. This value is bigger than any of the existing designs if placed in the same magnetic field. If more wires can be wound on the core, an even higher power density could be obtained. Therefore, the proposed design is a very efficient method for scavenging the magnetic field energy for a wide range of smart grid applications.