Control of the maglev system is one of the most significant technologies of the maglev train. The common proportion integration differentiation (PID) method, which has fixed control parameters, ignores the non-linearity and uncertainty of the model in the design process. In the actual process, due to environmental changes and interference, the inherent parameters of the system will drift significantly. The traditional PID controller has difficulty meeting the control requirements, and will have poor control effect in the actual working environment. Therefore, a radial basis function (RBF)-PID controller is designed in this article, which can use the information from the levitation system identified by the RBF network to adjust the parameters of the controller in real time. Compared with the traditional PID control method, it is shown that the RBF-PID method can improve the control performance of the system through simulation and experiment.
28 December 2021 in IEEE Transactions on Intelligent Transportation Systems
Superconducting (SC) electrodynamic suspension (EDS) has a wide application prospect due to the advantages of no active control, self-stability and large gap, especially in the ultra-high speed maglev, rocket launching, Electromagnetic Aircraft Launching System and other high speed fields. SC coils and null-flux Ground Coils which are the primary and secondary windings respectively are applied in a typical EDS system, in that the null-flux ground coils provide levitation and guidance force. The calculation of electromagnetic forces that has been extensively studied by scholars all over the world is the basis of the design and optimization of the system. However, due to the limitation of complex structure, the calculation formula is often so complicated that the results have to be obtained by means of finite element method and numerical simulation. This paper aims to derive an analytical calculation of electromagnetic forces for SC EDS system based on some reasonable assumptions. The experimental data of MLX01 on the Japanese Yamanashi testline was used to verify the calculation model of this paper. In order to get a further validation, a small EDS rotary table was built based on null-flux ground coils and permanent magnets. The results of the experiment confirms the effectiveness of the proposed analytical calculation model.
24 July 2024 in IEEE Transactions on Transportation Electrification
Due to the advantages of no active control, self-stability, large clearance, and small self-weight, the electrodynamic suspension system has a wide range of applications in high-speed fields such as ultra-high speed maglev transportation, electromagnetic ejection and rocket propulsion. The null-flux coil electrodynamic suspension system, as one of the typical representatives of electrodynamic suspension systems, has attracted the attention of researchers from all over the world and is expected to be commercially applied in Japan in 2027. The calculation method for the mathematical model of null-flux coil electrodynamic suspension system has been studied by many researchers and some effective conclusions have been obtained. However, due to the complex structure and large number of parameters of the null-flux coil electrodynamic suspension system, most of the existing calculation methods have complex equations and often have some assumptions and premises. This paper aims to derive the high-precision numerical and analytical calculation methods for the mathematical model of the null-flux coil electrodynamic suspension system without any excessive simplification or assumption, and to summarize the characteristics of the two methods. In order to get a further experimental verification, an electrodynamic suspension test system was built, and the high consistency between the test results and theoretical calculation results prove the correctness of the two calculation methods proposed in this paper, which paves a way for further analysis of the null-flux coil electrodynamic suspension system in the future.
5 November 2021 in Journal of Advanced Transportation
In order to analyze the dynamic response of medium-speed maglev train in the speed range of 0–200 km/h, the suspension performance, suspended energy consumption, and riding comfort of the train stimulated by random track irregularities are discussed in this paper. Firstly, the model of medium-speed maglev train including car body, air spring vibration isolation system, and the suspension system is established. Then, a controller based on flux inner feedback loop and PID outer feedback loop is designed for the suspension system. The established model is stimulated by the actual track power spectrum in full speed range. The simulation results show that the fluctuation of suspension gap is less than ±4 mm. Furthermore, thanks to the adding of permanent magnet, the power consumption is significantly reduced, which is of benefit to the electromagnet heating problem and on-board levitation power supply system. The riding comfort of the train moving on the irregular track using Sperling index is assessed. The experimental results validate the effectiveness of the proposed analytical calculation model of medium-speed maglev train. It is shown that medium-speed maglev train achieved good performance, significant power reduction, and satisfactory riding comfort.
Aiming at the problem of maglev train passing through the track joints, this paper proposes a Lyapunov-based backstepping controller for Magnetic Levitation System. First, the theoretical model of the maglev system is, and then, the theoretical formulae of the backstepping controller is deduced; to achieve rapid current response, a current loop feedback is designed. Second, a numerical simulation is carried out, and the simulation results show that the backstepping controller is not only simpler in design, but also faster in response. Finally, the designed controller is verified by experiments in the existing maglev system. The experimental results show that compared with the traditional PID controller, the backstepping method has a smaller overshoot and a faster response speed when dealing with the problem of a maglev train passing through the track joints. Also, it is more adaptable to external disturbances.
13 September 2018 in Transportation systems and technology
This paper is a study of the electromagnet-track coupled high frequency resonance that frequently occurs in the urban maglev systems, it includes the following points: Aim: The purpose of this study is to investigate the principle underlying the high frequency resonance occurs between the maglev train and the track, and to develop an appropriate vibration control algorithm which can be applied in the levitation controller, such that the resonance can be eliminated when the maglev train travels along the track. Materials and methods of the studies: In this paper, the model of the electromagnet-track coupled system is firstly established, in which some special cases, which correspond to the situations when the screws that fasten the F-rail to the sleepers are fatigue, or the stiffness of the rubber plates beneath the sleepers weaken for temperature reasons, are studied; and the reason that leads to the coupled resonance are explained as well. Secondly, an adaptive vibration control algorithm, which consists of a vibration observer and a tunable adaptive filter, is designed to suppress the high frequency electromagnet-track coupled resonance. Results: Using this algorithm, when the train arrives at the spots where the coupled resonance may occur, the vibration observer will detect the occurring of the vibration and estimates its frequency, and then activate the adaptive filter and tune it to absorb the vibration. Conclusion: The test indicates that this algorithm is capable of tuning itself to handle the unpredictable coupled resonance that occurs along the track, and it is simple and can be easily integrated into the levitation control code in a digital levitation control system.