The impact of dispersion effects on temporal-convolution-based real-time Fourier transformation (RTFT) systems, including the residual 2nd-order dispersion effect, the 3rd-order dispersion effect, and their joint effect, is theoretically analyzed. To reduce these effects, an optical RTFT system based on a bidirectional chirped fiber Bragg grating (CFBG) and an optical filter is proposed. Only one optical pulse source, a bidirectional CFBG, a Mach-Zehnder modulator (MZM) and a photodetector (PD) are needed. RTFT with a bandwidth of 40 GHz and a frequency resolution of 0.7 GHz has been experimentally achieved.
A coherent random-modulated continuous-wave (RMCW) LiDAR transmits a lightwave modulated by a pseudo-random binary sequence (PRBS). The lightwave backscattered from targets is received and used to reconstruct the PRBS. Then, the time-of-flight is extracted by correlating the reconstructed PRBS and the original PRBS. We propose a coherent RMCW LiDAR based on phase-coded subcarrier modulation, in which the impacts of internal reflection and optical Doppler frequency shift (DFS) are mitigated. A continuous lightwave is amplitude-modulated by an RF signal which is phase-coded with a PRBS. Coherent detection is used in the receiver. A beat signal that consisted of a low-frequency signal and a high-frequency signal is obtained by a single balanced photodetector (BPD). The optical DFS can be directly extracted from the low-frequency signal. It is used to compensate for the frequency offset of PRBS, which is extracted from the high-frequency signal. In addition, the background noise caused by internal reflection is suppressed by averaging over successive measurement spots. In this paper, the performance of a coherent RMCW LiDAR is firstly analyzed by numeric simulations and demonstration experiments. Then, line-scanning measurements for moving targets are implemented to demonstrate the 3D imaging capability of the proposed coherent RMCW LiDAR.
19 September 2022 in IEEE Photonics Technology Letters
A joint frequency-phase measurement is proposed for high-precision and fast laser ranging, in which a frequency-modulated continuous-wave (FMCW) method is used for coarse long-distance ranging, while a phase-shift method is used for high-precision ranging. Since a low-duty-cycle linear-frequency-modulated (LFM) signal is used, the precision of the FMCW method can be reduced to be smaller than the unambiguous distance of the phase-shift method. Therefore, fast phase unwrapping can be achieved for the phase-shift method using a small bandwidth LFM signal. In the experiment, a lightwave is simultaneously modulated by a 1–7 GHz low-duty-cycle LFM signal and a 15 GHz single-tone signal, which are frequency-separated so that the FMCW ranging and the phase-shift ranging can be simultaneously achieved. The measurement precision and measurement rate are $58~\mu \text{m}$ and 1.7 kHz, respectively. The measurement range can be 300 m. Therefore, the proposed method can be used to achieve laser ranging with kHz rate and decades of $\mu \text{m}$ precision at hundreds of meters distance.
Frequency-modulated continuous-wave (FMCW) laser ranging typically applies an interferometer and linear frequency-modulated (LFM) signals to measure the distance, in which precision and resolution are limited by the phase noise of laser and the bandwidth of LFM signals, respectively. This work proposes an FMCW laser ranging method that overcomes the limits of phase noise and bandwidth, in which the beat frequency of the LFM signals is estimated via time-domain maximum likelihood estimation. Using this method, super-resolved FMCW laser ranging can be achieved within the coherence length. It can also break the limits of phase noise, enabling laser ranging beyond the coherence length. An experiment is conducted. Using a 5 GHz bandwidth, a ranging resolution of 0.8 cm is achieved within the coherence length, which is enhanced by 5.1 times compared to traditional FMCW LiDARS. Moreover, beyond the coherence length, the ranging resolution and precision are enhanced by 10 times and 4.5 times, respectively. The enhanced performance is feasible even though the acquisition time is reduced to 20 μs. In addition, three-dimensional imaging of static and dynamic targets is implemented to show the enhanced performance. The proposed method enables long-range, fast FMCW laser ranging using a low-cost laser, which is also helpful to enhance the performance of interferometry.
Aiming at realizing comprehensive structural health monitoring, a GNSS (Global Navigation Satellite System) over fiber sensing approach is presented and experimentally demonstrated to achieve 3D nodal displacement and vibration detection simultaneously. GNSS signals from multi-antennas are transferred to a receiver based on an optical fiber link, also used as distributed sensing fiber. Broadband linear frequency-modulated (LFM) probe light with high linearity is generated based on electro-optic modulation to probe distributed vibrations and monitor the transmission time delay along the whole fiber with high precision. The spectral components generated by vibrations are detected using the cross-correlation method to achieve distributed vibration sensing. In addition, with the assistance of high-precision hardware-delay measurement, the variation of transmission time delay can be obtained, improving the precision of 3D displacement measurement in the GNSS-over-fiber architecture. In the proof-of-concept experiment, a 3D baseline can be obtained with the precision of 2.8, 3.6, and 2.0 mm, while vibrations with frequencies of 40 kHz, 80 kHz, and 100 kHz along 250 m fiber are successfully detected with a spatial resolution of 1 m.
28 November 2023 in IEEE Photonics Technology Letters
A novel microwave frequency division (MFD) architecture based on an optically injected distributed feedback laser diode (DFB-LD) with an optoelectronic feedback (OEO) loop is proposed. A radio-frequency (RF) signal is imported to the MFD for frequency division. As the optically injected DFB-LD works at Period-one (P1) state, the nonlinear effect of the intensity modulator in the OEO can split the P1 modes in the DFB-LD into a series of equi-spaced subharmonics. By properly tuning the parameters of the OEO, some frequency components generated in the OEO loop can be selected and amplified to interfere with the generated subharmonics due to the Vernier effect, which are equal to divide-by-n frequency division signals of the input RF signal. In the proof-of-concept experiment, divide-by-2 to 6 MFD of the RF signal around 18.0 GHz are realized. The signal-to-noise ratio (SNR) and phase noise of the division signals can respectively be enhanced to 59.6 dB and -118.32 dBc/Hz@10 kHz.