Recent J-TEXT research has highlighted the significance of the role that non-axisymmetric magnetic perturbations, so called three-dimensional (3D) magnetic perturbation (MP) fields, play in a fundamentally 2D concept, i.e. tokamaks. This paper presents the J-TEXT results achieved over the last two years, especially on the impacts of 3D MP fields on magnetohydrodynamic instabilities, plasma disruptions and plasma turbulence transport. On J-TEXT, the resonant MP (RMP) system, capable of providing either a static or a high frequency (up to 8 kHz) rotating RMP field, has been upgraded by adding a new set of 12 in-vessel saddle coils. The shattered pellet injection system was built in J-TEXT in the spring of 2018. The new capabilities advance J-TEXT to be at the forefront of international magnetic fusion facilities, allowing flexible study of 3D effects and disruption mitigation in a tokamak. The fast rotating RMP field has been successfully applied for avoidance of mode locking and the prevention of plasma disruption. A new control strategy, which applies pulsed RMP to the tearing mode only during the accelerating phase region, was proved by nonlinear numerical modelling to be efficient in accelerating mode rotation and even completely suppresses the mode. Remarkably, the rotating tearing mode was completely suppressed by the electrode biasing. The impacts of 3D magnetic topology on the turbulence has been investigated on J-TEXT. It is found that the fluctuations of electron density, electron temperature and plasma potential can be significantly modulated by the island structure, and a larger fluctuation level appears at the X-point of islands. The suppression of runaway electrons during disruptions is essential to the operation of ITER, and it has been reached by utilizing the 3D magnetic perturbations on J-TEXT. This may provide an alternative mechanism of runaway suppression for large-scale tokamaks and ITER.
In the last two years, three major technical improvements have been made on J-TEXT in supporting of the expanded operation regions and diagnostic capabilities. (1) The successful commission of the 105 GHz/500 kW/1 s electron cyclotron resonance heating (ECRH) system increasing the core electron temperature from 0.9 keV up to around 1.5 keV. (2) The poloidal divertor configuration with an X-point in the high-field side has been achieved. In particular, the 400 kW electron cyclotron wave has also been successfully injected into the diverted plasma. (3) A 256-channel electron cyclotron emission imaging diagnostic system and two sets of four-channel Doppler backscattering diagnostics have been successfully developed on J-TEXT, allowing detailed measurement of the electron temperature and density fluctuations for turbulence and MHD research. The locked mode (LM), especially the 2/1 LM, is one of the biggest threats to the plasma operation. Both the thresholds of 2/1 and 3/1 LM are observed to vary non-monotonically on electron density. The electrode biasing was applied successfully to unlock the LM from either a rotating or static resonant magnetic perturbation (RMP) field. In the presence of 2/1 LM, three kinds of standing wave (SW) structures have been observed to share a similar connection to the island structure, i.e. the nodes of the SWs locate around the O- or X-points of the 2/1 island. The control and mitigation of disruption is essential to the safe operation of ITER, and it has been systematically studied by applying a RMP field, massive gas injection (MGI) and shattered pellet injection on J-TEXT. When the RMP-induced 2/1 LM is larger than a critical width, the MGI shutdown process can be significantly influenced. If the phase difference between the O-point of LM and the MGI valve is +90° (or −90°), the penetration depth and the assimilation of impurities can be enhanced (or suppressed) during the pre-thermal quench (TQ) phase and result in a faster (or slower) TQ. A secondary MGI can also suppress the runaway electron (RE) generation, if the additional high-Z impurity gas arrives at the plasma edge before TQ. When the secondary MGI has been applied after the formation of the RE current plateau, the RE current can be dissipated, and the dissipation rate increases with the injected impurity quantity but saturates with a maximum of 28 MA s−1. The non-local transport is experimentally observed in the ion transport channel. The electron thermal diffusivity significantly increases with the ECRH power. Theoretical work shows that significant intrinsic current can be driven by electromagnetic turbulence, and the robust formation mechanism of the E × B staircase is identified from the Hasegawa–Wakatani system.
19 February 2018 in IEEE Transactions on Industrial Electronics
The low-frequency magnetic field immunity test usually requires a homogenous magnetic field inside a cubic space to demonstrate the interference field. However, the 3-dB homogenous magnetic field region generated by the commonly used the Helmholtz coil is not a cubic space, which indicates a suboptimal design. This paper proposes an improved two-coil configuration for low-frequency magnetic field immunity tests and other similar applications, and discusses two key issues related to its field inhomogeneity, namely winding cross section and installation misalignment. Three simple formulas are concluded to establish a relationship between the parameters of the improved coil and the required homogenous magnetic field. These formulas enable the parametric and fast design of the improved coil. A comparison with the Helmholtz coil shows that the improved coil can reduce over 10% conductor mass cost when the same homogenous magnetic field is required. In addition, the effects of winding cross section and installation misalignments on the field homogeneity are analyzed, and valuable suggestions are provided for the design of a practical coil system. At last, an experimental test and a finite-element analysis are performed. The results are compared with the theoretical analysis, and the validity of the main conclusions in this paper is proved.
The J-TEXT capability is enhanced compared to two years ago with several upgrades of its diagnostics and the increase of electron cyclotron resonance heating (ECRH) power to 1 MW. With the application of electron cyclotron wave (ECW), the ECW assisted plasma startup is achieved; the tearing mode is suppressed; the toroidal injection of 300 kW ECW drives around 24 kA current; fast electrons are generated with toroidal injected ECW and the runaway current conversion efficiency increases with ECRH power. The mode coupling between 2/1 and 3/1 modes are extensively studied. The coupled 2/1 and 3/1 modes usually lead to major disruption. Their coupling can be either suppressed or avoided by external resonant magnetic perturbation fields and hence avoids the major disruption. It is also found that the 2/1 threshold of external field is significantly reduced by a pre-excited 3/1 mode, which can be either a locked island or an external kink mode. The disruption control is studied by developing prediction methods capable of cross tokamak application and by new mitigation methods, such as the biased electrode or electromagnetic pellet injector. The high-density operation and related disruptions are studied from various aspects. Approaching the density limit, the collapse of the edge shear layer is observed and such collapse can be prevented by applying edge biasing, leading to an increased density limit. The density limit is also observed to increase, if the plasma is operated in the poloidal divertor configuration or the plasma purity is increased by increasing the pre-filled gas pressure or ECRH power during the start-up phase.
25 February 2020 in Plasma Physics and Controlled Fusion
Disruption prediction is essential for the safe operation of a large scale tokamak. Existing disruption predictors based on machine learning techniques have good prediction performance, but all these methods need large training datasets including many disruptions to develop their successful prediction capability. Future machines are unlikely to provide enough disruption samples since these cause excessive machine damage and the prediction models used are difficult to extrapolate to a machines that the predictor was not trained on. In this paper, a disruption predictor based on a deep learning and anomaly detection technique has been developed. It regards the disruption as an anomaly, and can learn on non-disruptive shots only. The model is trained to extract the hidden features of various non-disruptive shots with a convolutional neural network and a long-shot term memory (LSTM) recurrent neural network. It will predict the future trend of selected diagnostics, then using the predicted future trend and the measured signal to calculate an outlier factor to determine if a disruption is coming. It was tested with J-TEXT discharges in flat top phase and can demonstrate comparable performance to current machine learning disruption prediction techniques, without requiring a disruption data set. This could be applied to future tokamaks and reduce the dependency on disruptive experiments.