Retarders are important factors controlling the hydration and properties of magnesium potassium phosphate cements (MKPCs). Boric acid and borax are the most commonly used retarders for MKPC which could control the setting time in a wide range upon changing their content. However, with the increase in borax content, the early strength of MKPC can be reduced, and boron compounds are now included in the EU candidate list of substances of very high concern for authorization, due to their reproductive toxicity. Exploring alternative set retarders to boron compounds is, thus, of significance. This work investigated the effects of a candidate retarder, namely, sodium alginate, on the setting time, mechanical properties, hydration products, and microstructures of MKPC. Sodium alginate presented dramatically retarding effects on MKPCs in the range of 0% to 2% (by mass of water). One percent of sodium alginate by mass of water could extend the setting time of MKPCs from 15 min to 35 min, which presented a better retarding effect than borax (a typical retarder for MKPCs) and produced higher early strength of MKPCs. Adding no more than 1% of sodium alginate did not have a notably adverse effect on the formation of hydration product over the long term, but an unfavorable effect could be found regardless of the sodium alginate content, which could reduce the compressive strength of MKPCs.
Amorphous alloy fiber has the advantages of high tensile strength and high corrosion resistance compared with steel fiber, but its interfacial bonding with cement matrix is poor and requires surface modification treatment. In this study, the surface modification of amorphous alloy fiber was carried out by using silane coupling agent KH-550 solution, and its effect on the mechanical properties of ultra-high-performance concrete was investigated. The results showed that the amorphous alloy fibers modified with 15% concentration silane coupling agent KH-550 solution can effectively improve the mechanical properties of the ultra-high-performance concrete, where the interfacial bond strength with the cement matrix reached 3.29 MPa and the roughness reached 3.85. The compressive strength, flexural strength, tensile strength, and peak stress of the ultra-high-performance concrete mixed with modified amorphous alloy fibers could reach up to 133.6 MPa, 25.5 MPa, 8.32 MPa, and 114.26 MPa, respectively, which were 2.9%, 6.3%, 10.9%, and 4.3% higher than those of the ultra-high-performance concrete with unmodified amorphous alloy fibers. As the surface of the fiber was modified, its properties changed and the bonding effect with the cement matrix was better, which in turn improved the mechanical properties of the ultra-high-performance concrete.
This paper aims to provide new insight into a method to improve the chloride ion corrosion resistance of steel fiber reinforced concrete. The steel fiber was pretreated by zinc phosphate before the preparation of the fiber reinforced concrete. Interfacial bond strength, micro-hardness and micro-morphology properties were respectively analyzed in the steel fiber reinforced concrete before and after the chloride corrosion cycle test. The results show that the chloride ion corrosion resistance of the steel fiber was enhanced by zinc phosphate treatment. Compared to plain steel fiber reinforced concrete under chloride ion corrosion, the interfacial bond strength of the concrete prepared by steel fiber with phosphating treatment increased by 15.4%. The thickness of the interface layer between the pretreated steel fiber and cement matrix was reduced by 50%. The micro-hardness of the weakest point in the interface area increased by 54.2%. The micro-morphology of the interface area was almost unchanged before and after the corrosion. The steel fiber reinforced concrete modified by zinc phosphate can not only maintain the stability of the microstructure when corroded by chloride ion but also presents good bearing capacity.
Portland cement–silica fume binary cementitious materials are widely used in engineering construction and have been investigated from micro- to macroscopic aspects. However, the theoretical background on the hydration kinetics of the binary system has not been sufficiently covered in the literature. In this study, the hydration dynamic characteristics of the Portland cement–silica fume binary system curing at low temperature were investigated. Hydration kinetics equations were optimized and a hydration model followed by a computer program was developed to calculate the reaction rate constant K and the reaction order n. This model presented that the hydration process of the binary system at low temperature could be divided into three stages, namely, nucleation and growth (NG), interactions at phase boundaries (I), and diffusion (D). The n values for the binary system varied in the range of 1.2 to 1.6, indicating that the hydration of the binary system at low temperature was a complex elementary reaction. Silica fume can reduce the total heat at the later stage of the hydration and the reaction order n, but increase the heat flow at the accelerating stage and the hydration rate constant K. Low temperature prolonged the hydration induction period, decreased and delayed the secondary exothermic peak, as well as reduced the n and K value.