Guanhua Zhang

Dr. Guanhua Zhang


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2020 in Nanotechnology Reviews
Verified
Journal Article
Open access
PDF file
YLYushi Liu
Yushi Liu
MJMinjie Jia
Minjie Jia
CSChengzhe Song
Chengzhe Song
Shuang LuShuang Lu
Shuang Lu
HWHui Wang
Hui Wang
YYYingzi Yang
Yingzi Yang
In order to meet the increasing engineering requirements, the ultra-early strength of sulphoaluminate cement (SAC)-based materials need to be improved to achieve road repair, engineering rescue and other objectives. Graphene oxide (GO) of 0.04 wt% was incorporated into SAC mortar to prepare GO enhanced SAC mortar (GO-SAC). It was found that the compressive strength of GO-SAC was increased by 46.9% at the age of 6 hours, and the flexural strength of GO-SAC was increased by 121.4% at the age of 100 minutes, compared with the control SAC mortar. The mechanism analysis based on the characterization results derived from XRD, BET, in situ ATR-FTIR, hydration heat measurement, TG–DSC and SEM showed that, the addition of minute quantities of GO led to the formation and growth of ribbon-like AFt,which further resulted in the improvement of the ultra-early strength of GO-SAC. This work indicates that GO has great potential for practical application in the preparation of high-performance SAC-based materials with ultra-early strength.

4 January 2021 in Materials
Verified
Journal Article
Open access
PDF file
DLDong Lu
Dong Lu
JZJing Zhong
Jing Zhong
BYBaobao Yan
Baobao Yan
JGJing Gong
Jing Gong
ZHZiye He
Ziye He
CSChengzhe Song
Chengzhe Song
It has been reported that iron tailing powder (ITP) has the potential to partially replace cement to prepare ultra-high-performance concrete (UHPC). However, the reactivity of ITP particles in concrete largely depends on the curing method. This study investigates the effects of curing conditions on the mechanical and microstructural properties of UHPC containing ITP. To achieve this objective, three research tasks are conducted, including (1) preparing seven concrete formulations by introducing ITP; (2) characterizing their mechanical performance under different curing regimes; and (3) analyzing their microstructure by XRD patterns, FTIR analysis, and SEM observation. The experimental results show that there is an optimum ITP dosage (15%) for their application. The concrete with 15% ITP under standard curing obtains 94.3 MPa at 7 days, their early-age strength could be even further increased by ~30% (warm-water curing) and ~35% (steamed curing). The steam curing regime stimulates the activity of ITP and refines the microstructure. This study demonstrates the potential of replacing Portland cement with ITP in UHPC production.

26 January 2022 in Materials
Verified
Journal Article
Open access
PDF file
YYYuanquan Yang
Yuanquan Yang
BFBodong Fang
Bodong Fang
GZGuanhua Zhang
Guanhua Zhang
JGJinbo Guo
Jinbo Guo
RLRunqing Liu
Runqing Liu
Retarders are important factors controlling the hydration and properties of magnesium potassium phosphate cements (MKPCs). Boric acid and borax are the most commonly used retarders for MKPC which could control the setting time in a wide range upon changing their content. However, with the increase in borax content, the early strength of MKPC can be reduced, and boron compounds are now included in the EU candidate list of substances of very high concern for authorization, due to their reproductive toxicity. Exploring alternative set retarders to boron compounds is, thus, of significance. This work investigated the effects of a candidate retarder, namely, sodium alginate, on the setting time, mechanical properties, hydration products, and microstructures of MKPC. Sodium alginate presented dramatically retarding effects on MKPCs in the range of 0% to 2% (by mass of water). One percent of sodium alginate by mass of water could extend the setting time of MKPCs from 15 min to 35 min, which presented a better retarding effect than borax (a typical retarder for MKPCs) and produced higher early strength of MKPCs. Adding no more than 1% of sodium alginate did not have a notably adverse effect on the formation of hydration product over the long term, but an unfavorable effect could be found regardless of the sodium alginate content, which could reduce the compressive strength of MKPCs.

3 February 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
DHDongxu Hou
Dongxu Hou
THTieming Hu
Tieming Hu
GZGuanhua Zhang
Guanhua Zhang
Super-span, reinforced concrete, T-shaped cross-section beams (T-beams) with a service life of more than 30 years are widely used in highway bridges in China. Most of these beams have been retrofitted with glass fiber-reinforced plastic (GFRP) to prevent performance degradation. However, the actual shear performance, ultimate state, and failure mechanism of the existing retrofitted super-span concrete T-beams are currently unclear for many inextricable problems. To fill these gaps, in this study, one super-span concrete T-beam, in service for 31 years and retrofitted with GFRP, was extracted from a highway bridge to conduct shear experimentation in a structural laboratory. To assess the particularity of the specimen, finite element analysis was also conducted using ABAQUS software as a supplement to the shear tests. The failure procedure of the specimen was investigated, and the influence of the loading mode on the shear performance of a super-long and old T-beam was also studied. It is concluded that the failure of the super-span T-beam begins with small cracks at the bottom of the mid-span, rather than a loading point.

21 February 2019 in Multidiscipline Modeling in Materials and Structures
Verified
Journal Article
Closed access
JLJinliang Liu
Jinliang Liu
JYJia Yanmin
Jia Yanmin
GZGuanhua Zhang
Guanhua Zhang
JWJiawei Wang
Jiawei Wang
Purpose: The calculation of the crack width is necessary for the design of prestressed concrete (PC) members. The purpose of this paper is to develop a numerical model based on the bond-slip theory to calculate the crack width in PC beams. Design/methodology/approach: Stress calculation method for common reinforcement after beam crack has occurred depends on the difference in the bonding performance between prestressed reinforcement and common reinforcement. A numerical calculation model for determining the crack width in PC beams is developed based on the bond-slip theory, and verified using experimental data. The calculation values obtained by the proposed numerical model and code formulas are compared, and the applicability of the numerical model is evaluated. Findings: The theoretical analysis and experimental results verified that the crack width of PC members calculated based on the bond-slip theory in this study is reasonable. Furthermore, the stress calculation method for the common reinforcement is verified. Compared with the model calculation results obtained in this study, the results obtained from code formulas are more conservative. Originality/value: The numerical calculation model for crack width proposed in this study can be used by engineers as a reference for calculating the crack width in PC beams to ensure the durability of the PC member.

5 January 2023 in Iranian Journal of Science and Technology, Transactions of Civil Engineering
Verified
Journal Article
Closed access
PDF file
YDYixing Ding
Yixing Ding
JYJia Yanmin
Jia Yanmin
GZGuanhua Zhang
Guanhua Zhang
JWJiawei Wang
Jiawei Wang