For the evaluation of the structural effect of electrophiles on the regioselectivity of ambident anions, the reaction of phosphoryl allylic carbanion with p-substituted benzaldehydes was investigated.
1 October 2014 in Advances in Mechanical Engineering
Due to rapid development in the industry, operating speeds and eccentricity produced undesirable vibrations which may lead to damage in bearings, seals, and lubrication systems. In the proposed paper, a novel analytical method was presented using an integrated multi-body dynamics and finite element analysis to simulate the lateral and torsional vibration. This method was applied to a proposed model of single rotor-system. In order to study the lateral and torsional vibration of the system profoundly, three markers were placed on the locations of the left and right bearings and the mass center of the shaft. The effects of bearing force caused by lateral and torsional vibrations were also analyzed. The results showed that the lateral vibration has a great effect on the dynamic of single rotor-system when lowering motor speed. It was found that, as motor speed increased, the motion of the system becomes more stable with steady fluctuates of the displacement response. The calculated natural frequency of SRS is compared with theoretical results to verify the transient solver. This novel method is practical in analyzing the lateral and torsional vibration of the SRS under various speeds and eccentricities.
The vibration isolation system is now indispensable to high-precision instruments and equipment, which can provide a low vibration environment to ensure performance. However, the disturbance with variable frequency poses a challenge to the vibration isolation system, resulting in precision reduction of dynamic modeling. This paper presents a velocity self-sensing method and experimental verification of a vibration isolation system. A self-sensing actuator is designed to isolate the vibration with varying frequencies according to the dynamic vibration absorber structure. The mechanical structure of the actuator is illustrated, and the dynamic model is derived. Then a self-sensing method is proposed to adjust the anti-resonance frequency of the system without velocity sensors, which can also reduce the complexity of the system and prevent the disturbance transmitting along the cables. The self-sensing controller is constructed to track the variable frequency of the disturbance. A prototype of the isolation system equipped with velocity sensors is developed for the experiment. The experiment results show that the closed-loop transmissibility is less than −5 dB in the whole frequency rand and is less than −40 dB around, adding anti-resonance frequency which can be adjusted from 0 Hz to initial anti-resonance frequency. The disturbance amplitude of the payload can be suppressed to 10%.
1 January 2019 in Mathematical Problems in Engineering
In this study, the response surface (RS) method and forced rotordynamic analyses together with Finite‐Element‐Analysis (FEA) have been established to optimize the factors affecting the vibration characteristics. The spindle specification, bearings locations, cutting force, and motor‐rotor unbalance mass are proposed to represent the design factors and then they are utilized to develop Machine Motorized Spindle (MMS). The FEA‐based Design of Experiment (DOE) is adopted to simulate the output responses with the input factors, wherein these DOE design points are used to carry out the RS models to visualize more obvious factors affecting the dynamic characteristics of MMS. The sensitivities of these factors and their contributions to the vibration of imbalance response have been evaluated by using the RS models. The simulation results show that the motor‐rotor shaft inner diameter, the distance of the back bearing location, and the rotating unbalance‐mass are highly sensitive to the vibration characteristics compared to the other factors. It is found that more than two‐fifths of total vibration response amplitude has been conducted by induced rotating imbalance mass. The results also showed that the proposed factors optimization method is practicable and effective in improving the vibration response characteristics.
29 August 2022 in Advances in Mechanical Engineering
To solve the problem of performance degradation caused by supersonic phenomena under high gas supply pressures in orifice-compensated aerostatic journal bearings (OCAJBs), a double-row gas supply micron-groove-orifice aerostatic journal bearing (MGOAJB) is designed, and the SST k- ω turbulence model is used to analyze the influences of the supersonic phenomena on the gas film flow field under different gas supply pressures, gas film thicknesses and orifice diameters. Compared with traditional OCAJBs, under high gas supply pressure, supersonic phenomena occur near the gas film inlet in both the MGOAJB and the OCAJB. The Mach number, maximum pressure, temperature and Reynolds number of the OCAJB are higher than those of the MGOAJB, but the MGOAJB has a more stable gas film pressure due to pressure equalization. As the gas film thickness of the MGOAJB increases, the Mach number, Reynolds number and temperature near the gas film inlet increase, but the pressure decreases, the recovery of the pressure and temperature becomes more obvious when the gas velocity drops to a subsonic speed. With increases in the MGOAJB orifice diameter, the pressure, temperature and Reynolds number increase, the Mach number decreases, and the recovery of the pressure and gas temperature becomes more obvious.
6 February 2023 in Advances in Mechanical Engineering
To solve the problems of a low gas supply pressure and low load capacity of traditional orifice-compensated aerostatic journal bearings (OCAJBs), this paper presents the design of a double-row gas supply micro-groove-orifice aerostatic journal bearing (MGOAJB). By establishing new governing equations and introducing the SST k- ω turbulence model, the influence of the micro-groove-orifice (MGO) structure and its layout form on the static characteristics of aerostatic journal bearings under a high gas supply pressure are studied. It is found that under high gas supply pressure, the MGO structure can significantly improve the load capacity and stiffness and reduce the gas consumption of the MGOAJB compared with the OCAJB. With additional MGO structures in the eccentric direction of the spindle, the load capacity and stiffness of the bearing increase substantially, and the gas flow also increases. The layout direction of the MGO has a prominent influence on the static characteristics of the MGOAJB. Axial MGOs have a higher load capacity and stiffness and lower gas flow. The accuracy of the simulation method is verified by experiments. This study provides a theoretical basis and method for the design of aerostatic journal bearings under a high gas supply pressure.