Starting from the eighties, the use of nanoadditives registered an increasing attention in the scientific and patent literature, especially for the case of polymeric nanocomposites. In the last decade, this involved bituminous materials, modified either with nanosized fillers or with polymeric nanocomposites. One of the expected benefits is an increased resistance of the binder to aging. After a short introduction underlining the uncertainties and risks of artefacts in aging tests, a review is given, focusing on the antiaging properties of layered silicates, which are by far the most important nanoadditives for bitumens. Together with layered silicates, other materials such as nanohydrated lime, nanosilica, and layered double hydroxides are mentioned. Preparation and characterization of the binary bitumen/layered silicate and ternary bitumen/layered silicate/polymer systems are described in order to individuate the aspects that influence the antiaging effect. Even if the available literature is quite abundant and unanimously confirms that nanoadditives may improve bitumen durability, there is a lack of studies clarifying the involved mechanisms. As it is for conventional fillers, it seems to be a combination of physical and chemical interactions. Nanoadditives with different chemistries, porosities, and interlayer spacings differently absorb the polar components from the bitumen, thus affecting their predisposition to oxidative aging.

This study focused on the development of a novel biocomposite material formed by a thermoplastic biodegradable polyester, poly(butylene succinate-co-adipate) (PBSA), and a carbonaceous filler as biochar (BC) derived by the pyrolysis of woody biomass waste. Composites with various BC contents (5, 10, 15, and 20 wt.%) were obtained by melt extrusion and investigated in terms of their processability, thermal, rheological, and mechanical properties. In all the composites, BC lowered melt viscosity, behaving as a lubricant, and enhancing composite extrudability and injection moulding at high temperatures up to 20 wt.% of biochar. While the use of biochar did not significantly change composite thermal stability, it increased its stiffness (Young modulus). Differential scanning calorimeter (DSC) revealed the presence of a second crystal phase induced by the filler addition. Furthermore, results suggest that biochar may form a particle network that hinders polymer chain disentanglement, reducing polymer flexibility. A biochar content of 10 wt.% was selected as the best trade-off concentration to improve the composite processability and cost competitiveness without compromising excessively the tensile properties. The findings support the use of biochar as a sustainable renewable filler and pigment for PBSA. Biochar is a suitable candidate to replace more traditional carbon black pigments for the production of biodegradable and inexpensive innovative PBSA composites with potential fertilizing properties to be used in agricultural applications.

Polyurethanes (PUs) are one of the most versatile polymeric materials, making them suitable for a wide range of applications. Currently, petroleum is still the main source of polyols and isocyanates, the two primary feedstocks used in the PU industry. However, due to future petroleum price uncertainties and the need for eco-friendly alternatives, recent efforts have focused on replacing petrol-based polyols and isocyanates with counterparts derived from renewable resources. In this study, waste cooking oil was used as feedstock to obtain polyols (POs) for new sustainable polyurethane foams (PUFs). POs with various hydroxyl numbers were synthesized through epoxidation followed by oxirane ring opening with diethylene glycol. By adjusting reagent amounts (acetic acid and H₂O₂), epoxidized oils (EOs) with different epoxidation degrees (50–90%) and, consequently, POs with different OH numbers (200–300 mg KOH/g) were obtained. Sustainable PUFs with high bio-based content were produced by mixing the bio-based POs with a commercial partially bio-based aliphatic isocyanate and using water as the blowing agent in the presence of a gelling catalyst and additives. Various water (4, 8, 15 php) and gelling catalyst (0, 1, 2 php) amounts were tested to assess their effect on foam properties. PUFs were also prepared using EOs instead of POs to investigate the potential use of EOs directly in PUF production. Characterization included morphological, chemical, physical, thermal, and mechanical analyses. The rigid PUFs exhibited high density (150–300 kg/m³) and stability up to 200 °C. The combined use of bio-based polyols with partially bio-based isocyanate and water enabled PUFs with a bio-based content of up to 77 wt.%. EOs demonstrated potential in PUF production by bypassing the second synthesis step, enhancing sustainability, and significantly reducing energy and costs; however, PUF formulations with EOs require optimization due to lower epoxy ring reactivity.

In azidic binders for solid propellants, the N3 functionality is introduced by substitution of a halogen or tosyl group, but recently the mesyl group has been suggested as an alternative. The mesylate group has two advantages, mainly related to its small dimensions and low cost. Poly(glycidyl azide) and poly 3-azidomethyl-3-methyl oxetane were prepared by using both tosylate and mesylate precursors. The azidation kinetics were studied at three different temperatures while keeping all other operating parameters the same. The results confirmed the good potential of the mesylate precursors for the production of azidic binders

The increase in concrete structures’ durability is a milestone to improve the sustainability of buildings and infrastructures. In order to ensure a prolonged service life, it is necessary to detect the deterioration of materials by means of monitoring systems aimed at evaluating not only the penetration of aggressive substances into concrete but also the corrosion of carbon-steel reinforcement. Therefore, proper data collection makes it possible to plan suitable restoration works which can be carried out with traditional or innovative techniques and materials. This work focuses on building heritage and it highlights the most recent findings for the conservation and restoration of reinforced concrete structures and masonry buildings.