This paper studied the effect of additives of 0.5–20 wt.% synthetic CaSiO3 wollastonite on the thermodynamic, mechanical, and tribological characteristics and structure of polymer composite materials (PCM) based on ultra-high-molecular weight polyethylene (UHMWPE). Using thermogravimetric analysis, X-ray fluorescence, scanning electron microscope, and laser light diffraction methods, it was shown that autoclave synthesis in the multicomponent system CaSO4·2H2O–SiO2·nH2O–KOH–H2O allows one to obtain neeindle-shaped nanosized CaSiO3 particles. It was shown that synthetic wollastonite is an effective filler of UHMWPE, which can significantly increase the deformation-strength and tribological characteristics of PCM. The active participation of wollastonite in tribochemical reactions occurring during friction of PCM by infrared spectroscopy was detected: new peaks related to oxygen-containing functional groups (hydroxyl and carbonyl) appeared. The developed UHMWPE/CaSiO3 materials have high wear resistance and can be used as triboengineering materials.
The application of titanium and its alloys under friction conditions is severely restricted, owing to their poor wear resistance. The paper presents the results of studies of the composition, microstructure, and tribological properties of Ti-TiC-based composite coatings formed on titanium alloys by the electroarc treatment in an aqueous electrolyte using a graphite anode. It has been found that TiC grains have a different stoichiometry and do not contain oxygen. The grain size varies from hundreds of nanometers to tens of micrometers, and the micro-hardness of the treated surface reached the value of 29.5 GPa. The wear resistance of the treated surface increased approximately 40-fold, and the friction coefficient with steel decreased to 0.08–0.3 depending on the friction conditions. The formation of a composite material based on Ti-TiC will contribute to the effective protection of titanium alloys from frictional loads in engineering.
To study the material based on the binary system Ti + Cu (50% atm), samples were produced from powders of commercially pure metals and additionally ground in a ball mill (final size about 12 µm) by spark plasma sintering. The following intermetallic phases were obtained in the materials: CuTi2, TiCu, and Ti3Cu4. The materials have a hardness of 363 and 385 HV (800 and 900 °C), a microhardness of 393 and 397 µHV, a density of 4.24 and 5.23 kg/m3, and resistance to corrosion in acids (weight gain + 0.002% after 24 h of testing according to ISO 16151 for a sample with 900 °C—the best result in comparison with steel 308, AA2024, CuA110Fe3Mn2). The hardness value varies due to the presence of pure metal agglomerates. The relationship between the temperature of spark plasma sintering and the characteristics of the material (material parameters improve with increasing temperature, segregation is reduced) is revealed.
The article considers the effect of a filler based on synthetic wollastonite (CaSiO3), which is introduced into a polymer matrix made of ultra-high molecular weight polyethylene, on the tribotechnical parameters of the produced polymer composite material. Behavioral features of composites after friction were investigated by infrared spectroscopy and scanning electron microscopy. It was found that the introduction of wollastonite into the polymer matrix contributed to a reduction in the friction coefficient by 23% and the wear rate by four times. In the micrographs of the friction surfaces of the obtained composite, the formation of new secondary structures oriented along the friction direction, different from the initial polymer matrix, was revealed. The presence of wear products (oxidized polymer groups) and CaSiO3 on the friction surfaces was recorded by infrared spectroscopy. It was established that the synthesized CaSiO3 particles were deformed under the action of shear forces and participated in tribochemical processes.
1 December 2019 in Russian Journal of Inorganic Chemistry
The comparative analysis of sorption properties of nanostructured barium silicates obtained in multicomponent systems BaCl2 · 2H2O–КОН–SiO2–H2O and BaCl2 · 2H2O–КОН–SiO2–AlCl3–H2O has been performed to extend previous data; the data on the composition and morphology of the systems have been presented. Their properties toward sorption of Sr2+ ions from solutions of complex ionic composition have been studied. It has been found that synthetic barium silicates and alumosilicates have high sorption and kinetic characteristics under static sorption conditions. The maximal degree of Sr2+ ions recovery from solutions of complex composition (>99%) was achieved for barium silicate BaSiO3 · 2.3H2O. The samples of barium alumosilicate BaAl2Si2O8 · 2.6H2O have the same sorption characteristics within measurement error. It has been shown that the studied sorbents, allowing for their kinetic properties, may be recommended for the deep purification of solutions of complex ionic composition, seawater including, from strontium ions under static conditions.
1 September 2016 in Theoretical Foundations of Chemical Engineering