The utilization of biomass waste as a raw material for renewable energy is a global concern. Pyrolysis is one of the thermal treatments for biomass wastes that results in the production of liquid, solid and gaseous products. Unfortunately, the complex structure of the biomass materials matrix needs elevated heating to convert these materials into useful products. Microwave heating is a promising alternative to conventional heating approaches. Recently, it has been widely used in pyrolysis due to easy operation and its high heating rate. This review tries to identify the microwave-assisted pyrolysis treatment process fundamentals and discusses various key operating parameters which have an effect on product yield. It was found that several operating parameters govern this process such as microwave power and the degree of temperature, microwave absorber addition and its concentration, initial moisture content, initial sweep gas flow rate/residence time. Moreover, this study highlighted the most attractive products of the microwave pyrolysis process. These products include synthesis gas, bio-char, and bio-oil. The benefits and challenges of microwave heating are discussed.

Although heavy metals are typically found in trace levels in natural waterways, most of them are hazardous to human health and the environment, even at extremely low concentrations. Nanotechnology and nanomaterials have gained great attention among researchers as a sustainable route to addressing water pollution. Researchers focus on developing novel nanomaterials that are cost-effective for use in water/wastewater remediation. A wide range of adsorbed nanomaterials have been fabricated based on different forms of natural materials, such as carbonaceous nanomaterials, zeolite, natural polymers, magnetic materials, metal oxides, metallic materials, and silica. Hence, this review set out to address the ability of various synthesized nanoadsorbent materials to remove different heavy metal ions from water and wastewater and to investigate the influence of the functionalization of nanomaterials on their adsorption capacity and separation process. Additionally, the effect of experimental variables, such as pH, initial ion concentration, adsorbent dose, contact time, temperature, and ionic strength, on the removal of metal ions has been discussed.

Lignocellulosic biomass is a class of sustainable material that can be utilized as a raw feedstock in biofuel and chemical production. However, the complex matrix structure of lignocellulosic materials complicates conversion processes, such as enzymatic hydrolysis. Therefore, an efficient pretreatment process is required to disrupt the plant cell wall structure and maximize the recovery of valuable soluble components from lignocellulosic biomass during hydrolysis. In addition, an effective pretreatment method should use the minimum necessary amounts of energy and chemicals to minimize the cost of the end product. Further, it should reduce the formation of inhibitory compounds that affect enzymes and microorganisms during hydrolysis and fermentation, and it should be applicable to a wide variety of feedstocks. The research presented in this review has highlighted the pros and cons of the current technologies employed in pretreatment processes. Further study should be done to optimize and improve these technologies to enhance the efficiency of the production of biofuels and other valuable components.

Microwave-assisted Dilute Acid Pretreatment and Enzymatic Hydrolysis of Sago Palm Bark

Solar energy is considered one of the most important renewable energy resources, and can be used to power a stand-alone photovoltaic (SAPV) system for supplying electricity in a remote area. However, inconstancy and unpredictable amounts of solar radiation are considered major obstacles in designing SAPV systems. Therefore, an accurate sizing method is necessary to apply in order to find an optimal configuration and fulfil the required load demand. In this study, a novel hybrid sizing approach was developed on the basis of techno-economic objectives to optimally size the SAPV system. The proposed hybrid method consisted of an intuitive method to estimate initial numbers of PV modules and storage battery, an iterative approach to accurately generate a set of wide ranges of optimal configurations, and a Pareto envelope-based selection algorithm (PESA-II) to reduce large configuration by efficacy obtaining a set of Pareto front (PF) solutions. Subsequently, the optimal configurations were ranked by using an integrated analytic hierarchy process (AHP) and vlsekeriterijumskaoptimizacija i kompromisonoresenje (VIKOR). The techno-economic objectives were loss of load probability, life cycle cost, and levelized cost of energy. The performance analysis results demonstrated that the lead–acid battery was reliable and more cost-effective than the other types of storage battery.