Tjokorda Gde Tirta Nindhia

Tjokorda Gde Tirta Nindhia


Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2016 in International Journal of Environmental Science and Development
Verified
Journal Article
Open access
TNTjokorda Gde Tirta Nindhia
Tjokorda Gde Tirta Nindhia
ISI. Wayan Surata
I. Wayan Surata
ISI. Dewa Gede Putra Swastika
I. Dewa Gede Putra Swastika
IWI. Made Wahyudi
I. Made Wahyudi

1 May 2017 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
DNDNK Putra Negara
DNK Putra Negara
TNTjokorda Gde Tirta Nindhia
Tjokorda Gde Tirta Nindhia
ISI W Surata
I W Surata
Made SuciptaMade Sucipta
Made Sucipta

1 January 2015 in Journal of Clean Energy Technologies
Verified
Journal Article
Closed access
TNTjokorda Gde Tirta Nindhia
Tjokorda Gde Tirta Nindhia
ISI. Wayan Surata
I. Wayan Surata
IAI. Ketut Adi Atmika
I. Ketut Adi Atmika
DNDewa Ngakan Ketut Putra Negara
Dewa Ngakan Ketut Putra Negara
IAI. Putu Gede Artana
I. Putu Gede Artana

1 April 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
TNTjokorda Gde Tirta Nindhia
Tjokorda Gde Tirta Nindhia
JSJ. Schlacher
J. Schlacher
TLTanja Lube
Tanja Lube
Precision shaped ceramic components can be obtained by an emerging technique called Lithography based Ceramic Manufacturing (LCM). A green part is made from a slurry consisting of a ceramic powder in a photocurable binder with addition of dispersant and plasticizer. Components are built in a layer–by-layer way by exposing the desired cross- sections to light. The parts are subsequently sintered to their final density. It is a challenge to produce ceramic component with this method that yield the same mechanical properties in all direction. The fracture toughness (KIc) of of LCM-alumina (prepared at LITHOZ GmbH, Austria) was tested by using the Single-Edge-V-Notched Beam (SEVNB) method. Notches are made into prismatic bend-bars in all three direction X, Y and Z to recognize the value of fracture toughness of the material in all three directions. The microstructure was revealed with optical microscopy as well as Scanning Electron Microscopy (SEM). The results indicate that the fracture toughness in Y-direction has the highest value (3.10 MPam1/2) that is followed by the one in X-direction which is just a bit lower (2.90 MPam1/2). The Z-direction is found to have a similar fracture toughness (2.95 MPam1/2). This is supported by a homogeneous microstructure showing no hint of the layers used during production.

23 March 2020
Verified
Conference Paper
Open access
PDF file
ISI Wayan Surata
I Wayan Surata
TNTjokorda Gde Tirta Nindhia
Tjokorda Gde Tirta Nindhia
DWDwiki Marsetio Widagdo
Dwiki Marsetio Widagdo
Synthetic ropes are popular for application in marine boat as docking, anchor, tow, and sailing. The advantages of synthetic ropes are waterproof, strong and durable, can be designed for sinks or floats and able to stretches. Synthetic ropes are stronger, more resistant to rotting than ropes created from natural fibers. Synthetic ropes also possess certain disadvantages of slipperiness, and can be damaged more easily by UV light. Synthetic ropes is recognizes as a source of microplastic fiber pollutant in marine area. In this work a bark of Hibiscus tiliaceus three is introduced as candidate source of natural fiber for rope to reduce number of microplastic fiber pollutant from synthetic rope. The bark was taken from a trunk with diameter around 20 cm. The bark was immersed in water for 7 days and subsequently was soaked in 5% NaOH solution for 2 hours. Fiber obtained then was dried. It was prepared 7 valid single fiber samples. The average of tensile strength of single fiber obtained by using this method is found around 44.604 MPa. The average of Modulus elasticity E is found 365.864 MPa. The failure strain is found 11.6 %.

1 May 2017 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
TNTjokorda Gde Tirta Nindhia
Tjokorda Gde Tirta Nindhia
ISI Wayan Surata
I Wayan Surata
AWAri Wardana
Ari Wardana
This research is established for the purpose of the understanding the stability of the acidity of lubricant oil in biogas fuelled engine due to the absence of hydrogen sulfide (H2S). As was recognized that other than Methane (CH4), there are also other gas impurities in the biogas such as carbon dioxide (CO2), hydrogen sulfide (H2S), moisture (H2O) and ammonia (NH3). Due to H2S contents in the biogas fuel, the engine was found failure. This is caused by corrosion in the combustion chamber due to increase of lubricant acidity. To overcome this problem in practical, the lubricant is increased the pH to basic level with the hope will be decrease to normal value after several time use. Other method is by installing pH measurement sensor in the engine lubricant so that when lubricant is known turn to be acid, then lubricant replacement should be done. In this research, the effect of biogas desulfurization down to zero level to the acidity of lubricant oil in the four stroke engine was carried out with the hope that neutral lubrication oil to be available during running the engine. The result indicates that by eliminating H2S due desulfurization process, effect on stability and neutrality of pH lubricant. By this method the engine safety can be obtained without often replacement the lubricant oil.